Smart Array P400 in Slot 1
Bus Interface: PCI
Slot: 1
Serial Number: PA2240J9SU038D
Cache Serial Number: PA82C0D9STZ5QY
RAID 6 (ADG) Status: Enabled
Controller Status: OK
Hardware Revision: B
Firmware Version: 7.22
Rebuild Priority: Medium
Expand Priority: Medium
Surface Scan Delay: 15 secs
Surface Scan Mode: Idle
Wait for Cache Room: Disabled
Surface Analysis Inconsistency Notification: Disabled
Post Prompt Timeout: 0 secs
Cache Board Present: True
Cache Status: Temporarily Disabled
Cache Status Details: Cache disabled; requires reboot to enable cache.
Cache Ratio: 25% Read / 75% Write
Drive Write Cache: Disabled
Total Cache Size: 256 MB
Total Cache Memory Available: 208 MB
No-Battery Write Cache: Disabled
Cache Backup Power Source: Batteries
Battery/Capacitor Count: 1
Battery/Capacitor Status: OK
SATA NCQ Supported: False

Array: A
Interface Type: SAS
Unused Space: 0 MB
Status: Failed Physical Drive
Array Type: Data

One of the drives on this array have failed or has been removed.

Logical Drive: 1
Size: 279.4 GB
Fault Tolerance: RAID 1
Heads: 255
Sectors Per Track: 32
Cylinders: 65535
Strip Size: 128 KB
Full Stripe Size: 128 KB
Status: Interim Recovery Mode
Caching: Enabled
Unique Identifier: 600508B1001030364130433244300500
Disk Name: /dev/cciss/c0d0
Mount Points: / 14.0 GB, none 5.6 GB, /VM 149.0 GB, /NETWORK 110.8 GB
OS Status: LOCKED
Logical Drive Label: A00008105001438006A0C2D062A9
Mirror Group 0:
physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 0 MB, Failed)
Mirror Group 1:
physicaldrive 2I:1:2 (port 2I:box 1:bay 2, SAS, 300 GB, OK)
Drive Type: Data

physicaldrive 1I:1:1
Port: 1I
Box: 1
Bay: 1
Status: Failed
Last Failure Reason: No failure
Drive Type: Data Drive
Interface Type: SAS
Size: 0 MB

physicaldrive 2I:1:2
Port: 2I
Box: 1
Bay: 2
Status: OK
Drive Type: Data Drive
Interface Type: SAS
Size: 300 GB
Rotational Speed: 10000
Firmware Revision: HPD9
Serial Number: KLHTETKF
Model: HP EG0300FBVFL
Current Temperature (C): 32
Maximum Temperature (C): 39
PHY Count: 2
PHY Transfer Rate: Unknown, Unknown

unassigned

physicaldrive 2I:1:1
Port: 2I
Box: 1
Bay: 1
Status: OK
Drive Type: Unassigned Drive
Interface Type: SAS
Size: 300 GB
Rotational Speed: 10500
Firmware Revision: HPD0
Serial Number: Z320A184FTM91349
Model: HP EG0300FCSPH
Current Temperature (C): 31
Maximum Temperature (C): 35
PHY Count: 2
PHY Transfer Rate: Unknown, Unknown

↧

Re: cannot replace failed frive

February 20, 2014, 12:00 pm

≫ Next: Re: cannot replace failed frive

≪ Previous: cannot replace failed frive

Hello :)

You need to assign physicaldrive 2I:1:1 as spare for that array

↧

Re: cannot replace failed frive

February 20, 2014, 12:12 pm

≫ Next: Re: cannot replace failed frive

≪ Previous: Re: cannot replace failed frive

I can't:

starlnx1:~# hpacucli ctrl slot=1 array A add spares=2I:1:1

Error: This operation is not supported with the current configuration. Use the
"show" command on devices to show additional details about the
configuration.
Reason: Array is transforming

↧

Re: cannot replace failed frive

February 20, 2014, 12:25 pm

≫ Next: Re: cannot replace failed frive

≪ Previous: Re: cannot replace failed frive

Backup server data

Shutdown server

Replace failed drive with unassigned drive

Power on server and observe dialogs and prompt from P400 controller

(there might be a rebuild/repair ... can't remember exactly for P400 but here:

http://www.google.com/url?sa=t&rct=j&q=&esrc=s&frm=1&source=web&cd=2&cad=rja&ved=0CCoQFjAB&url=http%3A%2F%2Fh20000.www2.hp.com%2Fbc%2Fdocs%2Fsupport%2FSupportManual%2Fc00572169%2Fc00572169.pdf&ei=H2QGU96kHOLm7AbOyoGoCg&usg=AFQjCNGeuBB6ZXVU1hFiCPfYDVd2npst0Q&sig2=1NEYrl97c4GQD4uNpYDgsQ

↧

Re: cannot replace failed frive

February 20, 2014, 12:29 pm

≫ Next: Re: DL120 G6 LO100 Virtual KVM/Media Error Application Error Security Exception

≪ Previous: Re: cannot replace failed frive

I will try that. I have tryied so many things on this array that I am not sure if I have already done it.

I will let you know ...

regards

Kostis.

↧

Re: DL120 G6 LO100 Virtual KVM/Media Error Application Error Security Exception

February 20, 2014, 3:00 pm

≫ Next: replace of disks in RAID5

≪ Previous: Re: cannot replace failed frive

Hi...
I resolved this problem in the java configuration

try

A.- Start --> Control panel --> Java

B.- In the "Java Control Panel" --> "Security" tab and choose "medium"

C.- Clic "OK" and restart browser.

Regards

↧

replace of disks in RAID5

February 20, 2014, 11:31 pm

≫ Next: Re: Provisioning - Windows could not create a partition on disk 0

≪ Previous: Re: DL120 G6 LO100 Virtual KVM/Media Error Application Error Security Exception

On the DL380 G5 server the disk No. 8 in offline failed
The controler Smart Array P400, RAID5 from 8 disks, isn't present hot spare

I replaced a disk 8 on hot, I pulled out a disk and I inserted new without switching off the server
I passed rebuild the massif successfully
In Array Configuration Utility of mistakes any isn't present, the status at all OK
In diagnostics of HP System Management shows an error of reading/record on this disk

why? what I did wrong?

is possible to fix this error?

↧

Re: Provisioning - Windows could not create a partition on disk 0

February 21, 2014, 1:20 am

≫ Next: hp DL380 G5 network config.

≪ Previous: replace of disks in RAID5

Thanks, that's exactly what it was. Great tool, but only as good as the documentation that comes with it

↧

hp DL380 G5 network config.

February 21, 2014, 3:20 am

≫ Next: Re: replace of disks in RAID5

≪ Previous: Re: Provisioning - Windows could not create a partition on disk 0

Hi All,

After re-installing ESXi 5.X, I am able to configure only one NIC via network management screen.

We have 4 NICs, where can I configure the rest for static IP?

Thanks in advance.

Best Regards,

↧

Re: replace of disks in RAID5

February 21, 2014, 3:32 am

≫ Next: Re: 1783 smart controller E200i

≪ Previous: hp DL380 G5 network config.

You may try updating the firmware of the firmware. You may download the firmware from the following link:

http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=3288134&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253DMTX_9ed665a89aba447d925937f38b%257CswEnvOID%253D4064%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

Regards,

Vijayasarathy

↧

Re: 1783 smart controller E200i

February 21, 2014, 4:27 am

≫ Next: Re: Starting DL360 G6 without fully redundant fan setup

≪ Previous: Re: replace of disks in RAID5

Had that problem my self.. ditch the controller ...

↧

Re: Starting DL360 G6 without fully redundant fan setup

February 21, 2014, 6:26 am

≫ Next: Re: Starting DL360 G6 without fully redundant fan setup

≪ Previous: Re: 1783 smart controller E200i

Ensure that fans are populated at a minimum in fan1 and fan 2 and remove all components such as all expansion cards, riser cards and check if the server powers on. If so, then add one component at a time and power on the server to isolate component that could cause thermal issues.

Regards,

Vijayasarathy

↧

Re: Starting DL360 G6 without fully redundant fan setup

February 21, 2014, 8:37 am

≫ Next: SPP 2014.02.0 on Ubuntu 10.04.4 LTS

≪ Previous: Re: Starting DL360 G6 without fully redundant fan setup

Hi,

the server is not at my site, but in the datacenter. They tried to check which of the fans is broken and changed the slots of the different fan modules. It looks like something is broken with fan slot 4 and at the moment I think the fan element in slot 1 has a problem. Do I need to replace the systems mainboard when fan slot 4 is reporting an error with every fan module, even with one which works in another slot?

I do have a replacement server which is on his way to the datacenter at the moment. Therefore I need to wait until they send me the broken server back. Then I'll provide further information.

regards,

Andi

↧

SPP 2014.02.0 on Ubuntu 10.04.4 LTS

February 21, 2014, 9:43 am

≫ Next: Need to convert Raid 1+0 with spare to Raid 5

≪ Previous: Re: Starting DL360 G6 without fully redundant fan setup

Hi,

I'm trying to run hpsum from SPP 2014.02 on a DL360 G7 running Ubuntu 10.04.4 LTS x64.

When I run swpackages/hpsum this error is showed:

hpsum: 35: Syntax error: "(" unexpected (expecting "fi")

so I try to run directly /swpackages/x64/hpsum_bin_x64

and it shows:

hpsum_service_x64 started successfully on port 63001 and ssl port 63002.
Error: cannot launch browser.

The error about the browser is correct because I have no browser installed on system.

So using my pc browser I connect to https:/ip:63002 and I can run HP Smart Update Manager 6.2.0, but after inventory of baseline is done correctly, I receive "Inventory error" on "inventory of node" section.

Can someone please help me?

Thanks

↧

Need to convert Raid 1+0 with spare to Raid 5

February 21, 2014, 11:07 am

≫ Next: Re: cannot replace failed frive

≪ Previous: SPP 2014.02.0 on Ubuntu 10.04.4 LTS

I need to convert Raid 1+0 with spare to Raid 5 is it can be done with out data loss.

server space is near filledand have 80 GB free space in that logical drive(300)

I have HP DL385G6 server with smart array P410 with two SAS array.

array a is raid 1+0 with each 72 GB disk.

No need to change.

And Array B with Raid 1+0 with a spare disk.

Two 300 GB hard disk and one spare where the spare is failed now.

Please guide whether I may able to replace the failed spare disk with new one and delete the spare configuration and create Raid 5 configuration for this given below scenario without any Data loss

or We need to for look for a free slot.?

↧