Re: [ DL380P Gen 8 ] Window's Server OS Install Issue
Greetings!Please try out the following steps and let us know the result.1. Update Intelligent Provisioning to latest version using Intelligent Provisioning recovery Media 1.71. Please follow the...
View ArticleiLO 4 ProLiant DL360 Gen9 NAND read failure: Media is in a WRITE-PROTECTED state
Hi Everyone,One of our iLO 4 ProLiant DL360 Gen9 states iLO Health DegradedController firmware revision 2.10.00 NAND read failure: Media is in a WRITE-PROTECTED stateRunning ILO version 2.72 Oct 20...
View ArticleRe: iLO 4 ProLiant DL360 Gen9 NAND read failure: Media is in a...
Hello,I hope you are doing good.You need to follow (c04996097 & a00019495en_us) if the issue is not fixed end result is to replace the board as per the CA.Advisory: (Revision) HPE Integrated...
View ArticleRe: HPE DL580 G8 not booting from internal Drive
Hi kira12I never saw this message while observing the complete booting process.Anyway, I got the solution from another forum. I had to boot to System Utilities, then one time boot and there chose "Run...
View ArticleRe: ML350 Gen9 LFF
Check out this Document:https://h20195.www2.hpe.com/v2/gethtml.aspx?docname=c04375628under Core Optionsand:https://www.hpe.com/h20195/v2/GetHTML.aspx?docname=c04431235
View ArticleRe: ProLiant DL380 G6 Fan failure
Hi ,Actually, I didn't. Since, being a relatively old server, we did not have an HPE support contract, the only option they offered us was to send it for service repair. They would not even provide a...
View ArticleMIB / OID for Proliant ML350 gen 9
hi,I'm looking for the correct MIB file and OID's to monitor the hard drives, the power supply etc.Where can I find the correct file for this server? I have downloaded the MIB package, but there are...
View ArticleRe: ML110 G7 USB boot
That is correct. When you "Disable Legacy USB" Nothing on USB works during POST, including your USB Keyboard (and there is no PS/2 ports.) So you have to HARD RESET your BIOS to get back into it with a...
View ArticleRe: iLO 4 ProLiant DL360 Gen9 NAND read failure: Media is in a...
Thanks,So how can I access HP Smart Storage Array Administrator from bios (HPSSA)It detects no logical drives.This Proliant DL360 GEN8 has to be secure wiped (DBAN) prior to going back to HPE!
View ArticleRe: iLO 4 ProLiant DL360 Gen9 NAND read failure: Media is in a...
I had to boot via the SPP and use an interactive session to access HP Array Configurator which I have created two logical RAID 0 drives in readiness for 35 x DBAN secure wipe.
View ArticleGen10 System Reset without manual intervene
IML:Critical CPU Uncorrectable Machine Check Exception (Processor 1, APIC ID 0x00000018, Bank 0x00000003, Status 0xBE000000'00800400, Address 0xFFFFFFFF'811E3F3D, Misc 0xFFFFFFFF'811E3F3D). xx/yy/zzzz...
View ArticleRe: ProLiant DL380 G6 Fan failure
Thanks for your reply!I'll try with a new system board then ....BestAdot
View ArticleRe: iLO 4 ProLiant DL360 Gen9 NAND read failure: Media is in a...
Hello,You are correct,DBAN does not break down RAID arrays so the first thing is to create a RAID 0 array for each drive in the system.On power-up wait for RAID array, prompt and press F8 enter the...
View ArticleRe: DL-380 Gen 10 3 Fans always running at 94%Speed
Hello,Just want to let you know of a much simlper solution. Simply login to iLO and select "Cold Boot".That will do the trick, no need for any more trouble. This is always needed after firmware...
View ArticleFans in ML150 G6
Dear all,I have ML150 G6 with non-HP fans installed. I would like to: 1) Change threshods for fan. Current thresholds in Bios do not correspond to actual rpm and therefore I got events in impi.2)...
View ArticleRe: HP ProLiant DL380p Gen8 Riser card gets no power in its 10 pin plug
none of this worked.
View ArticleRe: [ DL380P Gen 8 ] Window's Server OS Install Issue
I upgraded the firmware and Intelligent Provisioning Some issues are resolved, such as it will now see the ISOs on the thumb drives, but no matter what approach I take, it still sits at 0% on...
View ArticleRe: HP Proliant DL580 Gen8 and GPU's
The HPE Proliant DL580 G8 is an enterprise product, as such is meant to only be compatible with enterprise grade GPUs. I can personally say that the Tesla M80 works on the DL580 G7. I have 2x Tesla...
View ArticleDL380p Gen8 | ILO Health Degraded & Display is turning black soon after OS...
Team,I'm facing the problem mentioned in the below url's. To start with, one day i noticed my server has stopped responding to mstsc but reachable via ping and C$ share is accessible. When I checked in...
View Article