Re: DL380 g4 black screen
Still the same problem - blank screen :-( No connections with ILO, Lan ( but status LEDs by the LAN cards are ok ). To Murali - I have 4 HDD . Maybe the best solution wiil be buying new server and...
View ArticleHow to add extra SAS hot plug drive on a ML 350 G6 running Windows 2012 server
How do i get to see a drive that is plugged in and shows online status when i log into ML 350 G6 running windows 2012 server under disk management. do i need special drivers to see it? i did not use...
View ArticleSata3 6Gbps support for these old models?
I want to change my disk to 1TB 7200RPM SATA 6Gbps 128 MB Cache for my old men which are;DL160 G6 - DL180 G6 - DL140 G3 where can I find if they support Sata3 which I feel they do not, Do I loose much...
View ArticleRe: How to add extra SAS hot plug drive on a ML 350 G6 running Windows 2012...
It is most likely connected to a smart array controller, so you should run ACU in order to configure it.
View ArticleRe: Disk Swap on DL320G5 P400 SAS
Yes. The RAID setup and status i stored on the disks. I will recommend that you ensure, that the spare server got at least the same FW/BIOS level, or newer as the failed server. BR/jag
View ArticleRe: Disk Swap on DL320G5 P400 SAS
Also, If the RAID controller need cache battery for RAID 5, and if you use RAID 5, ensure you got a battery o the spare server as well.BR/jag
View ArticleRe: VERY slow network after many HW updates on DL370 G6
SPP 2013.09.0B released yesterday finally includes an updated driver.Thank you HP !ftp://ftp.hp.com/pub/softlib2/software1/doc/p1822529277/v91225/SPP2013.09.0B-ReleaseNotes.pdf HP QLogic P3P...
View ArticleRe: Sata3 6Gbps support for these old models?
Hi,Unfortunately the controllers for G6 series do not support SATA3 (6Gbps). It only supports SAS (6Gbps) disks.You cannot get SATA3 support via a firmware upgrade....
View ArticleRe: Problems with Proliant DL560 Gen 8
This past weekend we experienced this error on two DL360P Gen8 servers. One went offline Friday and another went offline Sunday with the power fault message. A technician had to replace the...
View ArticleRe: Sata3 6Gbps support for these old models?
Can I still use sata3 disk? Or it wont be recognized?
View ArticleRe: Problem with ML350 G5 vs HDD p/n 507127-B21 vs Controller e200i
This problemisobservedon anyof the sameML350G5controllere200i,checkedon6servers.For example:p / n: 458242-421 (HP ML350T05 E5420 SAS SFF Array EU Svr)Removing Cache moduledoes not help.Raid...
View ArticleRed Light on HP Smartarray B110i Sata Raid - every 2 weeks - restart Server...
I have a problematic red light that appears on one of my PROLIANT DL160 drives (signalling bad drive) I have a simple RAID 1 array setup and am finding that the 2nd bay red lights every 2-3 weeks. A...
View ArticleRe: Sata3 6Gbps support for these old models?
As far as i know you may still use it , but it will be limited to the maximum speed supported by your controller (1.5 or 3 Gbps ).
View ArticleRe: VERY slow network after many HW updates on DL370 G6
Thanks for the update , i was looking for the release notes pdf and couldn't find it until i found your post :)
View ArticleML310e Gen8 memory voltage
Hello guys, I noticed on ML310e Gen8 with E3-1220v2 that LV SmartMemory runs at 1.5V intead of 1.35V I have 2x 647907-B21 (HP 4GB 2Rx8 PC3L-10600E-9 Kit)Power profile: Balanced Power and Performance...
View ArticleRe: ML310e Gen8 memory voltage
Hi, LV memory is supported on this server model according to the QuickSpecs. Here is an extract from RBSU user guide:Gen8 systems support both LV-DIMMs (1.35V) and 1.5V-only DIMMs. LV-DIMMs can switch...
View ArticleRe: Red Light on HP Smartarray B110i Sata Raid - every 2 weeks - restart...
Hi, Have you tried updating Server bios and or hard drive firmware to fix this issue apart from reseating the cables. Check the model number of the drive and see if there is any new firmware available...
View ArticleRe: DL380 g4 black screen
This could be issue with bad system board or component. If you have similar server you may try swapping parts to isolate further. Also, please not that these SCSI hard drivers may or may not support...
View ArticleRe: HP ML350e Gen8 Fan Noise
The problem is finally solved on my customers server. HP sent a technician onsite to replace the motherboard and the problem went away.
View Article