Re: Problems booting up G5 servers after firmware upgrades
I should add that on the servers that boot from CD-ROM through the Virtual Media applet from iLO2 I'm able to chroot into the existing installations and everything works as expected. I'm able to...
View ArticleRe: Problems booting up G5 servers after firmware upgrades
I should mention I've also checked the BIOS settings, messed with the IPL boot order and controller order in every possible way. I have even reset the BIOS settings on one of the servers with no result...
View ArticleRe: Ml110 G7 Fan speed.
Hi, I have just fitted the dedicated iLO port into my ML110 G7 and have found that Fan 8 is now only operating at 10%!!!! I don't know if this is as a result of having to remove and re-install the fan...
View ArticleHP ProLiant DL380p Gen8 Booting issue
Hi, I have a Brought a new HP DL380 Gen8 Server configured all parts . When i powered it on it powers on fine and shows the new boot-up display and shows the progress of system startup process but...
View ArticleRe: Ml110 G7 Fan speed.
Hi Garath,Could you post the exact expansion bit you used for the dedicated Ilo port? As you say for £25 I will try this.. I tired everything else. Its been switched off over the summer now as it was...
View ArticleRe: ML310e Gen8 not booting from USB Key with ESXi installed
I had the same problem but was able to get it to boot from USB using this guide: http://ares.gobien.be:8080/2013/06/vmware-esxi-5-1-on-usb-stick-wont-boot-proliant-dl380-g5/Right after choosing "Start...
View ArticleRe: Boot Proliant DL360 G3 from USB Drive
The easy fix for this is to replace the cd drive with a dvd drive
View ArticleRe: Ml110 G7 Fan speed.
Hi Rob, This is where I bought it from: http://www.ebay.co.uk/itm/400566815481 Alternatively, I believe the HP part number is: 514206-B21 I've had the server running all day today and it's still only...
View ArticleRe: ML110 G7 High Fan issue
Hi Guys, Just thought I'd add my recent findings after months of having a noisy ML110 G7, I've just fitted the HP dedicated iLO port and am now finding that Fan 8 is only running at 10%! I believe the...
View ArticleRe: Server Crash BSOD
as it turned out the DR process for Arcserve 16 is was not compatible with anyof the HP server 2012 drivers I was using ...I had to use Server 2008 64 bit drivers to gett his process to work
View ArticleNeed Processor Installation Tool?
I'm trying to install a second processor in an ML 350 G5. I ordered the processor and the heat sink. The manual says to use a plastic "processor installation tool" to insert the processor into the...
View ArticleRe: Ml110 G7 Fan speed.
Just to add, I've put my HDMI GPU in and the fan speed shot back up to 40%, with the card removed its back down to 10% so this may not be a solution for everyone, mine is now running non-standard HDDs...
View ArticleRe: ML110 G7 High Fan issue
Just to add, I've put my HDMI GPU in and the fan speed shot back up to 40%, with the card removed its back down to 10% so this may not be a solution for everyone, mine is now running non-standard HDDs...
View ArticleRe: Xeon E3-1220LV2 upgrade on G1610T Gen 8 Microserver
As far as I know it will work, but there may be a BIOS issue with adding a chip with gpu as the graphics are run through the matrox chip on the iLO. Check this blog out, this guy is my hero:...
View ArticleProliant ML150 G6 Server SmartStart and WIndows Install Software
I cannot locate the SmartStart and HP WIndows OS software for my Proliant ML150 G6 Server. I downloaded the smartstart software from the HP Support site but i cannot find the WIndows OS Install disk....
View ArticleRe: Proliant ML150 G6 Server SmartStart and WIndows Install Software
You will not be able to obtain os media from hp unless You have bought the os/license key it from hp, there is no free public os media download repository. You will have to provide it by yourself from...
View ArticleProLiant ML350p Gen8 - PCIe-Card / increased fan noise
hello, there is a ProLiant ML350p Gen8-Server with esxi in an office and everything was ok until a PCIe-graphic-card was built in.The fan speed is now increased from 6% to 25% but why? The...
View ArticleHP Proliant ML350 G6 temperatures
Hello, Recently i've started to manage the server from the subject.After a few days of running fine, today the server was found stopped, for no apparent reason. There's nothing in the logs. The server...
View ArticleRe: Need Processor Installation Tool?
Yes, you can do it by hand. The tool is useful if you have to work fast, but if you can take the time to be careful, it is not absolutely necessary.
View ArticleML350 G6 memory config. (Conflicting info)
Trying to upgrade the memory and from my perusing I am getting conflicting information (from HP and Crucial both). I have read in both places the max memory is 288GB, but I have also read that the max...
View Article