Hello,
I see none of the Ubuntu versions are supported for DL380 G5.
https://techlibrary.hpe.com/us/en/enterprise/servers/supportmatrix/exceptions/ubuntu_exceptions.aspx
for rest of the configuration please refer to the user guide
https://content.etilize.com/User-Manual/1011193914.pdf
Enabling access to the Array Configuration Utility (on page 70), Array Diagnostic Utility (on page
75), and Erase Utility (on page 72)
How about for Linux?
Thanks Torsten very helpful. All sorted now
The compatibility list for the mikrotik RB3011UIAS-RM at 10G SFP+ is this
https://wiki.mikrotik.com/wiki/MikroTik_SFP_module_compatibility_table#10G_SFP.2B
In it is specifies different modules
https://mikrotik.com/product/Splus85DLC03D
https://mikrotik.com/product/Splus31DLC10D#fndtn-specifications
https://mikrotik.com/product/Splus2332LC10D
https://i.mt.lv/cdn/product_files/splitter_modules_180841.pdf
https://mikrotik.com/product/SplusDA0001
https://mikrotik.com/product/s_ao0005
It says "They provide a low cost, low power and low latency interconnect solution for 10-Gigabit Ethernet, Fiber Channel and other industry standards, and are direct attached compliant and fully conform to the SFP+ MSA specifications"
But in the quick specification for the 530FLR I can't find any specification that leads me to any conclusion, more than a list of compatibility wich only includes proliant servers.
best regards
Yes, I know that it doesn't say that the DL360 G5 supports ubuntu, but it runs. If you open anything it's super slow, because the internal USB wasn't designed for systems with GUI. That's why I want to switch to a 2.5" SSD on SATA.
https://content.etilize.com/User-Manual/1011193914.pdf
I have seen this manual many times, even the one specifically for ACU on this website:
http://h10032.www1.hp.com/ctg/Manual/c00142272.pdf
None of those say how you enable the "select boot volume" back to the ORCA.
Also, will the Erase Utility delete the configuration of the ACU and ORCA?
.
How did you manage your Hpe Proliant server remotely?
sorry I'm still new to all of this
Hi
You need to clean the DIMM slots and DIMMs as well. Use the Deoxi kit to clean the DIMM and Slots
P04514-001 - SPS-KIT DEOXIT
Also perform the below.
or you can log a warranty case to organize for an Engineer visit to perform the above actions.
Reference: https://support.hpe.com/hpesc/public/docDisplay?docId=a00069107en_us
Hello,
I would suggest you have a proper case be logged with HPE, and share the appropriate logs for further analysis.
If you feel this was helpful please click the KUDOS! thumb below!
Regards,
Hello,
We have a client that would like to add six NVMe drives to their DL360 Gen10 server. They say that they would require riser / PCIe card support for 6 drives that are high performance ( minimum 2000/1000 mbps and ideally 3000/2000).
Currently the server has only two of the eight HDD slots filled.
Does anyone know - do they need a riser kit or is the machine already set up to take these NVMe drives?
Thanks!
Hello,
As I suggested in my last post, you have to follow the memory papulation guide.
If the issue still persists, I would suggest you have a proper case be logged with HPE, and share the appropriate logs for further analysis.
If you feel this was helpful please click the KUDOS! thumb below!
Regards,
Hello,
ILO always shows the correct information.
If you are facing any issues, update the system bios and ILO firmware with the latest as well as Agentless Management Service ( AMS).
Let me know if you have any other queries.
If you feel this was helpful please click the KUDOS! thumb below!
Regards,
Hello,
I would suggest you follow the below customer advisory.
https://support.hpe.com/hpesc/public/docDisplay?docId=a00060996en_us&docLocale=en_US
If the issue still persists, I would suggest you have a proper case be logged with HPE, and share the appropriate logs for further analysis.
If you feel this was helpful please click the KUDOS! thumb below!
Regards,
Hello,
As per the error message and snaps shots, the server should be updated with the latest bios and firmware.
If the issue still persits after update, the system board needs to be replaced.
If you feel this was helpful please click the KUDOS! thumb below!
Regards,
Hello,
* RECOMMENDED * ROM Flash Firmware Package - Server Platform Services (SPS) Firmware for HPE Gen10 Servers (04.01.04.381(B)(21 Aug 2020))
https://support.hpe.com/hpsc/swd/public/detail?swItemId=MTX_2fb0a1cdc3214eb18edaf78001
ROM Flash Firmware Package - HPE Gen10 Innovation Engine Firmware for HPE Gen10 Servers (0.2.2.0(1 Apr 2020))
https://support.hpe.com/hpsc/swd/public/detail?swItemId=MTX_641abebae642483b823c2dcc23#tab-history
Problems Fixed:
Addressed an extremely rare issue where Processor or Memory temperature reporting may not be collected properly by the platform and the system fans may be running faster than expected. This issue has been seen occasionally after a server reboot and is typically corrected with a subsequent server reboot
If you feel this was helpful please click the KUDOS! thumb below!
Regards,
Hello,
I would suggest you check the cable connectivity between SA P440AR controller to SAS expander to hard disk backplane.
Update the SAS expander controller firmware with the latest.
If the issue still persists, I would suggest you have a proper case be logged with HPE, and share the appropriate logs for further analysis.
If you feel this was helpful please click the KUDOS! thumb below!
Regards,
Hello,
i just bought an used Proliant DL380 G7 from Ebay and i wonder which hpe hdds i can use. I found this site https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-c02755440#N10012
But the problem is i cant find any of those hard drives on any online shop. Is it possible that i use "newer" hard drives that arent listed for this server? (like this one: https://www.ebay.de/itm/HPE-450-GB-6G-10K-SAS-2-5-Smart-Carrier-G8-G9-HDD-652572-B21-653956-001/114194233179?epid=118256174&hash=item1a9681b75b:g:CrkAAOSw9rJenrrL)
Thanks
Hi Carl,
As I understand you are trying LDAP configuration in ILO4. Please clarify on which server model you are trying to configure?
Kindly refer the below document for Directory Server Settings and ensure all pre-requisites and configuration is met.
Pg: 70 - Directory Server Authentication and Authorization.
https://support.hpe.com/hpesc/public/docDisplay?docId=c03334051
Directory Group Settings:
https://support.hpe.com/hpesc/public/docDisplay?docId=a00045203en_us&docLocale=en_US
IF still authentication issue seen, kindly log a support case to investigate this further.
Thanks,
HPE Employee.
I have a DL380 with a Smart Array P440ar. I have two issues:
1. Event Viewer reports NTFS error :
A corruption was discovered in the file system structure on volume D:A corruption was found in a file system index structure. The file reference number is 0xe60000000013fd. The name of the file is "\MyStorage\5\369". The corrupted index attribute is ":$I30:$INDEX_ALLOCATION".
2. When I run a diagnose with Smart Storage Administrator it reports that Cache is permanently disabled.
I have no other errors.
Is these two errors linked some how?
For NTFS error: Do I need to run Run CHKDSK /R or is there another way to solve it with the Smart Storage Administrator?