Re: HP ML350e Gen8 Fan Noise
Tried pulling the Thermal cable connector and re-booted - showed 0C/32F but no difference to fan noise, fans 1 & 2 are still around 43%, fan 3 is 34 % and fan 4 is 6%, have now replaced the cable....
View ArticleWhat the heck is wrong with the FTP servers for the HP downloads????
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=15351&prodSeriesId=3884319&prodNameId=3884320&swEnvOID=1005&swLang=8&mode=2...
View ArticleRe: High CPU Temp on Proliant G7 Servers
Hello, not yet. It did not happen again. If it does i will apply the firmware. GreetsStephan
View ArticleRe: Setup IPMI on HP DL 380 G8
I have already turned off the firewall, i did something like : # setup --> remove the asterisk (*) on the Enabled.# service iptables stop# chkconfig iptables off i think the firewall should be turn...
View ArticleRe: What the heck is wrong with the FTP servers for the HP downloads?
One worked fine for me just now, using firefox.
View ArticleRe: Setup IPMI on HP DL 380 G8
The syntax should be: ipmitool -H <hostname/IP> -I lanplus -U <username> -P <password> chassis power status ^ just for...
View ArticleRetired servers
I have two retired ML350 servers. One is an ML350 G3 and the other is an ML350 G4p. I am considering using one or both of them for storage or low level applications. I realize the G3 will not take...
View ArticleDL 385p Gen8
Hello, We recently aquired a DL 385p gen8. All drivers have been installed except for a device that does not says exactly what it is. It is under Other Devices by the name of "Base System Device" (It...
View ArticleRe: Retired servers
Hi, ProLiant OS Matrix does not show ML350 G4p as compatible with Windows 2008 but drivers web page does show Windows 2008 drivers. ML350 G4p Drivers and ProLiant Operating System Support Matrix Thank...
View ArticleRe: DL 385p Gen8
Hi, This is usually iLO device or the Chipset on the system board.Have you installed the below two drivers, if not, do install them. HP ProLiant iLO 3/4 Channel Interface Driver for Windows X64...
View ArticleRe: .net error on start "light-out online configuration utility"
You may try this link for previous version of the utility:...
View ArticleRe: ML110 G7 can't see additional drive
Is the previous hard drive a third party drive? Regards, Vijayasarathy
View ArticleRe: DL580 G4 memory board rebuild error
I am afraid it is boar failure - is your server still under suport? Jan
View ArticleRe: DL360e GEN8 Dynamic Raid Controller
Hello, it seems you are right, in ubuntu you can not use this software raid.but, here in RH: https://access.redhat.com/site/articles/118133 you can see there is HP driver forth to try.Check download...
View ArticleRe: DL360e GEN8 Dynamic Raid Controller
The current supported Linux distributions for the "B" series Smart Array controller are RHEL and SLES. CentOS should work with the RHEL driver here is the link for the latest driver for RHEL 6 x86_64...
View ArticleRe: Raid Migration inc Exchange Data
That looks like a 128 BBWC for a 640 controller, are you sure that's the part #? You can easily verify once the drives are inserted because if you have no BBWC then the options are greyed out.
View ArticleClik here to view.
DL310e Gen8, iLO 4 reports 1783-Slot X Drive Array Controller Failure, but...
I have a DL310e Gen8 server with a p222 FBWC SmartArray controller. I'm using iLO 4 Standard. Relevant ROM/firmware versions: The server's system ROM is: J04 12/10/2012.iLO 4's Firmware: 1.22 Apr 19...
View ArticleRe: Win 2008 R2 on DL585 G1
I found the solution, I had loaded 2 G1 servers with 2008 R2 no problem then I blew everything out and could not get them to reload. After a week of racking my brain I remembered the servers had 2003...
View Article