Re: HP DL380 gen 10 Runtime Fault, Processor(Intel), Processor 1 (04h))
Hello,Could you share the complete error message?Like: Server Critical Fault (Service Information: Runtime Fault Memory Processor 1 Memory Channels 4-6 (04h)) As per share error message, the system...
View ArticleRe: HP DL 580 Gen 8 - GPU instalation
Hello Wishgranter042, Greetings,Regret for all the inconvenience caused and the trouble you have undergone to resolve your query.We are glad to know that the query is fixed now. HPE published customer...
View ArticleProliant microserver gen8 - data recovery
Hello everyone,I have a proliant microserver gen 8 that is totally dead. I'm not be able to turn on it again. I want to get back the data inside the raid 5, configured with PCI card smart array p410. I...
View ArticleRe: ML350p Processor Upgrade - Steps and parts?
You can always use the HPE Support site for any information about any HPE products. To be more specific, please refer to the following link for a complete information about ML350p Gen8...
View ArticleRe: Hard Drive Swap
Let us know if we have answered the query, if not, write back for clarification.Thank you
View ArticleRe: Advice about DL380 gen 10 disk options
Please let us know if the query was answered. If not, write back for more clarification.Thank you
View ArticleRe: Proliant microserver gen8 - data recovery
Hi,P410 constoller is supported on G6 and G7 servers so you can try to move drives to any G6/G7 server with same controller and check.If logical drive detected, enable it from SSA then you should be...
View ArticleRe: ML350p Processor Upgrade - Steps and parts?
Thanks for the clarification on those two parts!One thing i don't see linked to that part in the Part Surfer is any sort of documentation. I imagine the kit must come with something "official" showing...
View ArticleRe: ML350p Processor Upgrade - Steps and parts?
The installation instructions will be available with the package. Alternative, instructions can be found from the below...
View ArticleRe: HpCISSs3 Error 5008, 129, 153 + Cissesrv 24607 = freezing VMs on node
Thank you for sharing the reports of both the controllers. The H241 controller does not have any drives connect internally & I hope it is used to connect the MSA. P440ar controller has two drives...
View ArticleRe: HpCISSs3 Error 5008, 129, 153 + Cissesrv 24607 = freezing VMs on node
After reviewing the reports that were shared through the FTP, we confirm that the issue is not within the server. It could on the MSA port or path connected to Node A.If this is an FC connectivity,...
View ArticleRe: RAM capacity vs. speed trade-off
It is by design the maximum limitation per channel for a fully populated Memory modules in a server.Please refer to the qucikspecs of the specific server model for more information.Thank you
View ArticleRe: HPE G10 MicroServer
Please let us know was there any changes made to the server due to which the issue is observed now?What is the controller to which the 4x 3.5 drives & the SSD's are connected?How many SSD's...
View ArticleRe: HP ProLiant DL 380 G7 iLO3 static IP problem
Is there any other devices which connects to mikrotik router which has a static IP address assigned ?If yes, is that device connects / has successful ping?Is there any link lights at the ILO Port?
View ArticleClik here to view.
Re: ML350p Processor Upgrade - Steps and parts?
Thanks for another quick reply! Can you tell me where the two fans (one for each new CPU) would be installed and from where they would draw power? I removed the air baffle and looked everywhere for a...
View ArticleRe: Am I getting optimal performance from my ML350p G8?
Replying to my own thread here ...Today I upgraded my RAM. After opening up my server I discovered one of the 2 x 8 GB DIMMs was in the wrong slot for processor 2! Maybe this was the cause of my slow...
View ArticleRe: ML350p Processor Upgrade - Steps and parts?
Required number of fans are already installed in the server as per the photos & the part number on the parts:667254-001Fan module assembly - 92mm x 92mm (3.62 inches x 3.62 inches) - Includes latch...
View ArticleRe: HP DL 580 Gen 8 - GPU instalation
Hi AmRa be sure i have tested even this with placing the GPU in slot 9, as i have seen even this recomendation. even this was fixed if remmeber in later BIOS updates and etc. ( tested every slot...
View ArticleRe: Maximum drive storage configuration ML350p G8
Replying to another of my own threads regarding adding extra drive cages.The ML350p G8 has two SAS connectors on the motherboard. These two connectors are disconnected from the first drive cage. An...
View ArticleRe: HPE server Automatic Power-on selection inactive
May I please request for a screen shot of the option that is not active? This would help us to identify the issue & provide assistance.Also share the server model name & product number.Thank you
View Article