Re: support pack 9.10
Please excuse me, but this is not true. I can confirm that it must apply the update SPP2013. there are many customers have had problems with the new version of SPP2014. check Release Note Page [11]:...
View ArticleProLiant ML310e Gen8 - Upgrading Hard Disk Backplane?
Hello, I have a HP ProLiant ML310e Gen8 Server with Xeon E3-1220v2, and it comes with a non-hot-plug disk bays. After spending some time looking in the manuals, it seems that an upgrade to Hot Plug...
View ArticleRe: ProLiant ML310e Gen8 - Upgrading Hard Disk Backplane?
HP Drive cage optionsHP 4U 4 Large Form Factor Hot Plug Hard Drive Backplane Kit 674839-B21HP 4U 8 Small Form Factor Hot Plug Hard Drive Cage Kit 674841-B21
View Articlehpsmh heartbleed
Hi, We discovered that hpsmh (version 7.2.2-8) is vurnerable for the OpenSSL Heartbleed problem on tcp port 2381, when will HP fix this issue? Is it possible to manual patch the embedded openssl? Alwin.
View ArticleSmart Array P410i, adding logical drives
Hi, I have HP ML350 g6 with P410i controller. One array with Two logical drives. Two physical drives in bay 1 and 2 of the server. I just installed two more physical drives in bay 3 and 4 of the...
View ArticleRe: Smart Array P410i Controller Configuration
AeroTwin7 wrote:Hi, I have HP ML350 g6 with P410i controller. One array with Two logical drives. Two physical drives in bay 1 and 2 of the server. I just installed two more physical drives in bay 3 and...
View ArticleRe: ML310 G5 AND SMART ARRAY P410 PROBLEM.
FINALLY SOLUTION: hardware replacement need on P410 SA! Now DS1 led check error always server start! Same problem in this post:...
View ArticleClik here to view.
HP Smart Array P410 Controller Firmware update alert in boot up
Hi All, Seek for your advice, i've an message when my server boot up such as below: Figure 1 : Message show when server boot up So i try to update the firmware, download from...
View ArticleRe: Intelligent Provisioning 1.60 breaks 2008 R2 install (will not accept...
v1.5 of the "Intelligent" Provisioning did the trick for me too. Thanks very much everyone :) George.
View ArticleRe: HP Smart Array P410 Controller Firmware update alert in boot up
This version is too old...
View ArticleRe: Intelligent Provisioning 1.60 breaks 2008 R2 install (will not accept...
In "HP Intelligent Provisioning 1.60 Release Notes". I find this at page 6 Windows-specific issues• The Volume License installation does not complete when you use the Recommended installation method to...
View ArticleRe: RAID controller driver for ML310 G5
Noone has an answer for my question?Even also about my question about where can I find the log file generated by the installer of the driver? Thanks in advance
View ArticleHP Proliant ML350 Gen 8: How to set up the disks.
Hi, We are about to install a new HP Proliant ML350 Gen 8 server on to one of our sites and the job of setting up the server has been assigned to me. Out of the box the server has by default set up...
View ArticleRe: cant remove rails for DL360 G5
I manage to remove the server using waste Car Key , Inserted the key both side (one by one) and push the latches !
View ArticleRe: support pack 9.10
Jimmy Vance wrote: "I've gotten from the SPP team, you can go from any version to the latest. There is no requirement to do a version to version upgrade." Scharchouf wrote: "this is not true. I can...
View ArticleRe: ML350 G5 with an Smart Array E200 fails
Hi - Were you ever able to resolve this? over 1500 views and no solution...
View ArticleMonitoring 6i controller in SLES 11
Hi all: I am looking for a way to monitor the hard drives in al old DL385 G1 server with a Smart Array 6i controller. I had to upgrade one of our old servers to SLES11 SP2 which broke HD monitoring....
View ArticleRe: support pack 9.10
I've never had a problem skipping SPP versions. The only possible problem I can think of is on Windows 2008 R2 and earlier, where some versions of the Network Config Utility depend on a certain version...
View ArticleRe: DL380G6 download drops
What version is the NIC driver? There were issues with 7.8.6.0 (I think that was the one). Make sure it's not that one... 7.8.50.0 is the latest driver for that NIC (the Broadcom gigabit multifunction...
View Article