Re: Cannot SSH into ILO4 v1.40 or v1.50 after upgrading from v1.32
Does your SSH client support Diffie Hellman group 14? In iLO4 v1.40, we enhanced the security of its SSH server by adding support for the DH group 14 for KEX (2048bits). If your SSH client doesn't...
View ArticleRe: Hard Drive Swap On HP ProLiant ML370 G6
Torsten. wrote:If this is the only problem with the raid (no other bad disks etc), pull the disk out and insert a new disk. The rebuild will start immediately.I'd suggest; pull the disk out, give the...
View ArticleRe: Hard Drive Swap On HP ProLiant ML370 G6
Hi, Many thanks for help. New drive swapped and rebuild OK. Only issue is that i have the following warning when I run a Diagnostoc on the p410i Postition 8Dirty Cache Line Unable To Flush To...
View ArticleE200/64 array controller can not recognize 6G-10K-300G hard disk
I have a few of DL380 G5 servers which have E200/64 array controller installed in them. Currently all servers have 72Gx2(RAID1) hard disks . They working fine in them. When I try to add the new ordered...
View ArticleRe: SPI Board REV??
This is for the DL 585 Server. We are having issues that are causing Gapping on our 10GB NICS as well as we are also seeing some CPU Stalls. From different critical messages we have seen it appears...
View ArticleRe: ML350p Gen8 - Hard Drives, SBS and Controller??
Just to sent my feedback, my server is not an ML350p, is an ML310e Gen8 v2. That ML310e Gen 8 v2 comes with 4 NHP caddies, so I connected 4 Seagate Constellation ST2000NM0033 and they work just fine....
View ArticleHP Proliant Server ML110 G5 Powered Up But No Post & Video.
After trying to install a PCI video card, my Proliant server ML110 G5 ( P/N 445069-001) was toatlly locked up. It powered up , the cooling fans were running, the motherboard LEDs and the front panel...
View ArticleRe: Cannot SSH into ILO4 v1.40 or v1.50 after upgrading from v1.32
Thank you. Adding the additional option to the command line worked.I will have to look into updating my ssh client. # ssh -o KexAlgorithms=diffie-hellman-group1-sha1 Administrator@hostnameWarning:...
View ArticleRe: DL580 G3 & VMware 5.1 U1 - Enable 64bit OS Support & SAHF and LAHF support
Do all 3 servers have the same System ROM BIOS?
View ArticleRe: E200/64 array controller can not recognize 6G-10K-300G hard disk
You can try to upgrade the firmware of the drives to the latest version. Use your G7 to do this.
View ArticleRe: HP Proliant DL380 G5 NIC's not found after firmware update
Try to reinstall the drivers for the NIC. I did it from Windows Update on Windows Server 2012 R2 and after a restart, the OS displays them as "HP NC373i Multifunction Gigabit Server Adapter" again.Geir
View ArticleRe: E200/64 array controller can not recognize 6G-10K-300G hard disk
Hi, E200 QuickSpecs does show this drive as compatible.DL380 G5 QuickSpecs also shows this drive as compatible.The option part for spare part# 507284-001 is 507127-B21. Try the following:If you are...
View ArticleRe: HP Proliant Server ML110 G5 Powered Up But No Post & Video.
Hi, After installing the PCI Video card, did you plug the monitor cable to the new pci card?To troubleshoot, did you remove the PCI Video card and tested the server for No Post?Is the new PCI Video...
View ArticleRe: Issues Updating U320 FIRMWARE
Hi, This error "write buffer failed" comes up when issue is with hard drives or controller.Issue could be with hard drive backplane or cables as well. Thank You!I am a HP employee.
View ArticleRe: HP DL320e Gen8 V2 - Won't boot from Ubuntu Install DVD
Hi, B120i software RAID mode must either be disabled or switched to SATA AHCI support mode.Try this:1. Go into RBSU during POST.2. Navigate to HP Smart Array B120i Raid Configuration.3. Change to...
View ArticleRe: ProLiant DL160 G5 with E200 controller recoginzes not all physical drives
Hi, DL160 G5 QuickSpecs states as follows: Internal Drive Support:Support for up to four 3.5" Non-Hot plug serial ATA (SATA) hard drives or;Support for up to four 3.5" Hot plug Serial Attached SCSI...
View ArticleRe: HP Proliant Server ML110 G5 Powered Up But No Post & Video.
Hi Suman_1978, Everything was ok before the installation of the PCI video card in slot 1. Yes, I did plug the cable to the new video card but there was no signal and no Post. I removed the video card...
View ArticleRe: Smart Array P420i extremely slow writes
Waroonb was right, there was a problem with the firmware/write cache. After upgrading til controller firmware 5.42, it seems like the problem is fixed, and we have been running now for a week with this...
View ArticleRe: CPU Upgrade in DL160G8 question about VRM/PPM
Hello, With the last bad news. I finally contact another HP reseller in my country to find another expert on Proliant server.He tells me that for my server, the "entry eu" model, the TDP is limited to...
View Article