hp-OpenIPMI failing
I have an ML350 G6 server running SLES 11 (x64). I cannot get hp-health or hp-snmp-agents to run, apparently due to an issue with hp-OpenIPMI. When I go to /opt/hp/hp-OpenIPMI and run...
View ArticleRe: hp-OpenIPMI failing
In the log for hp-health, it says: BUILD ERROR: Build for KERNEL VERSION: 3.0.101-0.7.17-default LINUX_BUILD_DIR: /lib/modules/3.0.101-0.7.17-default/source FAILED Failed to Build for the currently...
View ArticleRe: Unable to execute the file CP013142.scexe
Oh quit wining IT people :) The SCEXE stands for component executable and it is a Linux archive; to extract copy it to any Linux box and use the --unpack parameter by specifying some directory for the...
View ArticleBoot to CDROM Issue of iLO3...
Hi every masters,I mount the local image by iLO's Remote Console.I find even I set the CDROM as the priority one boot device of RBSU or press F11 to control 1/0 (People can see the below picture -...
View ArticleRe: Proliant DL380e Gen8 Uncorrectable Machine Check Exception
I had similar problem on my gen8 server in last week. Its showed both processors "Uncorrectable Machine Check Exception" error. I did bios upgrade to "2013.12.20" version and observed the sever...
View ArticleRe: end of life and support
Hi, can you tell me about end-of-support(-Packs) pf the HP Proliant ML370 G4 ? Thanks
View ArticleRe: boot failure after ip settings
I didn't made any change since last successfull boot of Centos. I'm sure. When it restarted, the problem was found. Before that the OS was booting from HDD (in raid 1). ... So, How can I define logical...
View ArticleRe: boot failure after ip settings
If there is data on the drives now, it will be gone after the RAID creation ... I would start with only the 2 disks that hold the OS, remove the other disks and power on.
View ArticleRe: boot failure after ip settings
Thank you Torsten.Your replies really helped me.I didn't notice to array configuration at all and didn't notice that logical volume should be defined.finally using below link i could configure and my...
View ArticleRe: boot failure after ip settings
OK, but I wonder where you did the OS installation before ... ?
View ArticleRe: boot failure after ip settings
OS was installed, because when i defined array, it booted without any problem. But I don't know that why this array configurations were removed!
View ArticleRe: HP PROLIANT DL385P G8 HALT ON POST
Hi EveryoneI have the same problem ,How could I fix IT .is there any solution for that ? any help I;ll be apppericiate . hkarimnejad@outlook.com
View ArticleRe: Using Powershell for ILO to set ILO IPv6 Parameters?
Sorry, I havent been able to figure it out. The only idea I have at the moment is to combine the traditional HP ILO scripting tool kit and disable all the IPv6 settings with a one time shot. Then,...
View ArticleRe: DL380 G5 Riser Bus Unresponsive
Hi, Did you try any known good x8 cards in those slots? What I guess is either the x8 slots are bad or SiI3132 does not support x8 bus width. Thank You!I am a HP employee.
View ArticleRe: ESXi 5.5 VMDirectPath 'workaround' mentioned in Customer Advisory c03835455
Hi, Did you call HP Support for help on this issue? If not, please call, them may have a solution. Thank You!I am a HP employee.
View ArticleRe: hp-OpenIPMI failing
Hi, I recommend following the Installation Instructions and its Prerequisities. The Linux kernel .config file must have IPMI support enabled for rebuilds.If a previous version of the hp-OpenIPMI...
View ArticleRe: Proliant DL360 G6 Accelerator Board Battery Failed
Many thanks for your help, I really appreciate, and I like the idea of the 4 AAA batteries, unfortunately for me it won't be accpeted I'm sure of this.I have one more question, is there any other way...
View ArticleProblem downloading latest Service Pack for ProLiant DVD
I have tried to download the latest SPP DVD (2014.06.0) and get the message "Access to the kiosk product denied.There is no product associated with this merchant.Please check with your support." I...
View ArticleRe: Unable to HP Service Pack for ProLiant With Active Care Pack
Me too ...What's the point in having something really useful like the SPP DVD then cocking up making it availableAlec
View ArticleRe: Unable to HP Service Pack for ProLiant With Active Care Packs
Thanks for that waaronb, I'll check the checksum against the HP site (its under installation instructions on the SPP 2014.06.0 web page) For those also after it see post above, Message 5 md5sum file is...
View Article