Re: DL380p Proliant Intelligent Provisioning Failure
I'm just posting this for completeness. I reconfigured an existing ProLiant ML350e Gen8 server today. I updated Intelligent Provisioning from 1.50 to 1.60 (HPIP160.2014_0113.271.iso). I was then able...
View ArticleRe: SAS HBA for DL380 G6
Hi The HP H221 Host Bus Adapter QuickSpecs confirms that the HP H221 Host Bus Adapter is, only compatible with the HP Proliant DL380 Gen8 series server series. However, the HP SC08e Host Bus Adapter...
View ArticleRe: DL785 G6 Windows 2012?
Hello I agree with Jan Soska that an HP Sales representative would be the way to go. I have contacts that I can put you in touch with if you would like. Another option is to contact HP Total Care to...
View ArticleRe: Brand new DL380 G7 fans question
Maybe it will be better once you've installed the OS and the HP software, where the system agents can take over fan speed control. Worth a shot.
View ArticleRe: Drive Upgrade in hotplug RAID1
I update arrays all the time with larger disks using the "replace one at a time" option. If the drives are hot pluggable there's no reason to do it with the system turned off... that would mean...
View ArticleRe: USB 3.0 on ML350p Gen8
Omniscient wrote:Sorry to revive an old thread...I wanted to ask Senator if the fan speed increased in the 350p Gen 8 server after QT587AA was installed?We had a Startech USB 3.0 card, it uses the same...
View ArticleRe: Drive Upgrade in hotplug RAID1
Thank you for your reply. We have P4xx controllers on a G5, 6 and 7's. Can you please advise: How can I check if these controllers have a battery backed cache?How did you start the online expansion...
View ArticleHP ProLiant DL380e Gen8 - Second processor did not power up
I'm installing a brand new HP ProLiant DL380e Gen8 - Xeon E5-2403V2 1.8 GHz - Server (748204-S01) and have added a second Intel Xeon E5-2403V2 - 1.8 GHz CPU (708495-B21).The server stops i POST with...
View ArticleMicroserver Gen 8 stops recognizing array
Hello, I have a brand new Proliant Microserver Gen8. I've done the following:- I updated Intelligent provisioning to 1.6.- I created a mirror RAID.- I installed Windows Server 2012 R2 Foundation.-...
View ArticleProLiant DL380G5 NOT BOOTING
Hi Guys I've got a ProLiant DL380G5 the problem is when i power it up i dont see any thing on monitorand fans are remaine at high speed with loud noise and server shows no errors...??? Any Ideas?
View ArticleRe: POST Error: 1792-Drive Array Reports Valid Data Found in Array Accelerator
This error pops up in log viewer if an unexpected shutdown had happened? Check does server had a power outage?This message will appear that means the data is the in memory of your raid card waiting to...
View ArticleRaid Advice On DL360 G7
Hi. I am quite familiar with HP Proliant servers and Also Windows Server OS's But today I was called out to a DL360 G7 running SBS2011. It has in total 4 Hot Swap Drives and one of them is flashing...
View ArticleRe: Need help installing additional Raid Controller on ML350 G5
Hi, Regarding power to the additional hard drive backplane, check the cables on the power supply backplane if any one of them can be connected to the hard drive backplane. Ref to the attached image:1-6...
View ArticleRe: ML350G4p w/Smart Array 641 install W2008x64 R2 fails at load drivers for...
Hi, ML350 G4p does not support Windows Server 2008 R2.Downgrade to Windows Server 2003. http://h17007.www1.hp.com/us/en/enterprise/servers/supportmatrix/windows.aspx Thank You!I am a HP employee.
View ArticleRe: HP ProLiant ML350 G6 - F8 to access iLO2 setup doesn't appear
Hi, Some suggestions:1. Clear NVRAM from System Maintenance Switch.If clearing NVRAM does not work.2. Update BIOS and iLO Firmware and see if that makes a difference....
View ArticleRe: HP ProLiant DL380e Gen8 - Second processor did not power up
Hi, If possible swap the processors. Proc 1 in Slot 2 and Proc 2 in Slot 1 and see if issue follows slot or processor. Either the processor and slot could be faulty. Its a good idea to update BIOS to...
View ArticleRe: ProLiant DL380G5 NOT BOOTING
Hi, Bring the server to minimum configuration, remove add-on cards which are not required for booting.Try with minumum RAM. If the server boots fine with minimum configuration, then add parts one by...
View ArticleRe: Proliant DL360 G8 & Server 2012R2
Sorry Didn't see your reply until today but that is the fix I had a ticket in with HP & it wasn't until I got the ticket elvated to Level 2 that I got that fix. I guess it's been documented here...
View ArticleUnable to install WBEM management agents on ProLiant DL380 G6 (Windows)
I have a ProLiant DL380 G6 running Windows 2008 R2 Enterprise (SP1). I am trying to install the WBEM agents on it (latest - 9.50) and it is failing. Tried rebooting too - still fails. Here is the...
View ArticleRe: ML350G4p w/Smart Array 641 install W2008x64 R2 fails at load drivers for...
Thank youAfter many hours of trying, I figured that out so I had already downgraded to 2003
View Article