Re: Setup IPMI on HP DL 380 G8
Please go into the iLO web interface, under Administration - Access Settings, look under IPMI/DCMI and verify the checkbox is selected "Enable IPMI/DCMI over LAN on Port 623"
View ArticleProLiant DL380 G7 - Over temp error
We have had 3 new DL380 G7s running on burn in for a couple weeks. this morning I went to configure iLO and when I rebooted the server the system health led shows red, the over temp led shows amber,...
View ArticleHP System Management Homepage Blank
The problem has been discussed in may thread, in the net.I've read most of them but my HP M.H. is still empty.New HP ML 350 G8, fresh installedHP System Management Homepage v7.1.2.3SNMP service...
View ArticleRe: ProLiant DL380 G7 - Over temp error
Check if the server fans are working. Reseat them if not swap them. If the issue persists, then reseat internal components. If the issue persists, then remove any PCIe expansion cards, remove all DIMMs...
View ArticleRe: ProLiant DL380 G7 - Over temp error
Thanks for the suggestions, I reseated all the fans and pulled the DIMMS right away. When I started it none of the 6 front fans ran at all.
View ArticleP420/i Array Configuration Recommendations for SQL Server
Have a new DL380 G8 server that I'll be installing MS SQL 2012 on, under Windows 2008 R2. The DB/application in question is write heavy. I was wondering if anyone from HP, or others with experience,...
View ArticleRe: DL380 G8 HP SUM Updates Not Complete
Does HP monitor and respond to these forums? And, is this post in the proper section? Thanks.
View ArticleRe: DL310e Gen8, iLO 4 reports 1783-Slot X Drive Array Controller Failure,...
1785 error comes up if "A Smart Array Controller is installed but not used". I guess you are not using B120i so this error is coming up. Refer to this doc about 1785 error. That seems logical, I just...
View ArticleRe: DL585 with RAID and/or HD issues
OK. There is a lot of info there. Under the "Consolidated Error Report" section it only lists the two drives in predictive failure. I will try to replace one tomorrow and see if that fixes it. It...
View ArticleRe: ML350 G5 won't boot, red internal health LED, undocumented system board...
I have the same problem I suppose. The internal health led is blincing red I don't get anything on the screen will powering up. I allready tried removing all RAM, removed the battery, turned switch...
View ArticleRe: Can't update firmware ML310e g8
The problem I reffer is the following: Intelligent Provisioning / ACU - doesn't start. Story:1. I've started the Server, set-up the RAID, installed Windows for testing RAID drivers purpouse, wen't...
View ArticleRe: Upgrading Hard Drives on HP ProLiant DL360 G5 Server - Best Practice
Thanks Derick for the reply. I'm runing RAID 1 and I have read that if I swap out one drive at a time, then wait for it to finish mirroring, and then do the other the same way, then all that would ned...
View ArticleRe: hpacucli Interim Recovery Mode + transforming
In this case, dont have problem, do you can replace this disk just pull the disk and put another.
View ArticleHELP.. 3 new 628059-B21 came up SMART fail after first reboot (DL 180 G6 P410...
I just bought three 3TB SATA drives(628059-B21) installed them set up a RAID 5 and got my volumes set up and put some data on them. Everthing looked good until I rebooted when it suddenly became...
View ArticleDL380e G8 : Post Error: 1785 Drive Array Not configured
Hi guys, I have a small problem that I didn't manage to resolve with my new Proliant DL380e G8. The Smart Array Controller says on boot:1785 Drive Array Not configuredNo drives detected When I press F5...
View ArticleRe: Any way to connect status/activity LEDs from Areca ARC-1160 to ML150 G2...
Any details about the connectors on the hot swap SATA backplane in the ML150 G2 or pointers where to find them would also be greatly appreciated!
View ArticleProblem with a disk and smart array Proliant DL380p Gen8
Help please! Hp Diagnostics has shown the message: Error: 640004: Controller has reported a critical performance threshold error on this driveWarning: The warranty period for this hard drive may have...
View ArticleMl 330 G6 Fan Pinouts
Hi, I bought a Ml330 G6 but it has no fan installed Does anyone have the pinouts for the 6 pin fans ? Cheers Joe
View ArticleRe: DL380 G4 - HDD migration from DL380 G3
Hi Derick The 300GB HDDs are all Maxtor brand...not actually HP.They were working inthe G3 though...so I'd be surprised if they weren't compatible with the G4.Or maybe I would be surprised :DWill
View ArticleRe: DL380 G4 - HDD migration from DL380 G3
I've just swapped out the 300GB didks for genuine HP 146GB ones.....and they're not recognised either. Faulty controller perhaps?
View Article