Re: DL380 G4 - HDD migration from DL380 G3
Double check all scsi cabling is ok especially check for bent pins on the 68 pin connectors. Also check the terminator module on the hot plug backplane for bent pins too. if you dont see anything try...
View ArticleFault tolerance configure for DL165 and D2600
Hi, I have two DL 165 G7 servers and a single D2600 disk array. At the moment the D2600 is directly atached to a single server using a P411 HBA. Is it possible to connect the d2600 to two separate...
View ArticleRe: DL380e G8 : Post Error: 1785 Drive Array Not configured
Hello, HP Dynamic Array Controller B120i (embedded on this server) does not support SAS hard drives. It only support SATA drives. 516810-003 HP G8 600-GB 6G 15K 3.5 SAS SD So, you should purchase SATA...
View ArticleHP IP Console No Keyboard..
Hello, I have a "HP IP and Server Console Switch G2 (With Virtual Media) Connected to a HP DL380p." The keybord works in the Device its self, to configure IP address etc.. but when you connect to the...
View ArticleRe: Problem with a disk and smart array Proliant DL380p Gen8
Hello, I would raise a support call with HP on this if you have support. I would also try to reseat the battery back cache module, its streight forward enough, just disconnect the battery and reconnect...
View ArticleRe: DL380 G4 - HDD migration from DL380 G3
Thanks for those suggestions Mark, I'll give that a go tomorrow and report back!
View ArticleRe: Fault tolerance configure for DL165 and D2600
You can't with a D2600. The reason is that the intelligence is in the SmartArray P411 controller, and that server is maintaining the disk system.You do have two options:1) Manual failover - if you have...
View ArticleRe: SPP/MCP/SRD Support for Citrix XenServer 6.x?
Thanks for your note. The short answer is unfortunately no. This isn't by choice either....
View ArticleRe: HP IP Console No Keyboard..
Are you sure the dongle from the server to the KVM is connected properly?
View ArticleHP advisory says to update to iLO 3 1.57 or later, yet 1.55 is all that is...
http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/kb/docDisplay/?spf_p.tpst=kbDocDisplay&spf_p.prp_kbDocDisplay=wsrp-navigationalState%3DdocId%253Demr_na-c03787836-1%257CdocLocale%253...
View ArticleCan't Boot SPP-2013.02.00 on DL365 (G1)
I've downloaded the Service Pack for ProLiant 2013.02.0 .iso, burned it to DVD, and verified that it was successfully created:eric@eric-D630 ~ $ isoinfo -d -i /dev/sr0 CD-ROM is in ISO 9660 format...
View ArticleRe: Can't Boot SPP-2013.02.00 on DL365 (G1)
FWIW: I'm able to reliably boot the system and run HP Insight Diagnostics using the SmartStart CD Release 8.70 x64.
View ArticleRe: Can't Boot SPP-2013.02.00 on DL365 (G1)
epretorious wrote:FWIW: I'm able to reliably boot the system and run HP Insight Diagnostics using the SmartStart CD Release 8.70 x64.I've run HP Insight Diagnostics (Full Test) on both machines and...
View ArticleRe: HELP.. 3 new 628059-B21 came up SMART fail after first reboot (DL 180 G6...
Hi, Once we had a similar issue where all hard drives were showing Predective failure.Later found out that issue is with the hard drive backplane. In your case the issue could be with drive backplane...
View ArticleRe: Fault tolerance configure for DL165 and D2600
Thanks David. I think option one will have to do then. The HBA was originally bought with a battery backed cache but that controller failed, was replaced and I am not sure if the new controller has...
View ArticleRe: BSOD - Pulled from web! - HP SA SAS/SATA Controller Driver for Windows...
Stop ERROR from minidump DRIVER_IRQL_NOT_LESS_OR_EQUAL (d1) An attempt was made to access a pageable (or completely invalid) address at aninterrupt request level (IRQL) that is too high. This is...
View ArticleRe: BSOD - Pulled from web! - HP SA SAS/SATA Controller Driver for Windows...
Hi, The attached log shows:MODULE_NAME: HpCISSs2IMAGE_NAME: HpCISSs2.sys HPCISSS2.SYS is part of Smart Array SAS/SATA Controller Driver. And here is the Customer Advisory you are looking for. Thank...
View ArticleRe: ProLiant ML 570 G3 power up issues
Hi,As suspected the power backplane was the issue with the server. Replaced with a good working part and now the server is up and running again. Thank you for all your support, J
View ArticleRe: BSOD - Pulled from web! - HP SA SAS/SATA Controller Driver for Windows...
Thanks! I got an HP Alert e-mail with the advisory :)You beat me to it :)Case closed
View ArticleRe: ML350 G4 Can't boot any disk
1. Be sure to check the boot order setting in the BIOS.2. Have you considered trying an external USB CD/DVD drive? I keep one around for ocassions such as these.HTH,
View Article