HP ACU - No controllers detected (DL380 Gen9)?
I have DL380 Gen9 installed via Provisioning with Windows Server 2012. The RAID array has been created during provisioning. I have also downloaded the latest HP ACU (9.40.12.0) and installed it. But it...
View ArticleDL380 G6 2NIC visible other 2 are not - in RSBU enabled - not seen in PCI IRQ...
So the issue is this, the server had to be turned off due to electricity excercise.When the server was turned back on only 2 out of 4 NICS (excluding ILO) were visible in Windows. With the result that...
View ArticleRe: DL380 G6 2NIC visible other 2 are not - in RSBU enabled - not seen in PCI...
Clarification the line which reads The NIC cards in ILO instead of the MAC address it displays Disabledshould beThe NIC cards which are working I can see there MAC address whilst the one not working...
View ArticleModifying Logical Drive Setup
Hi!So in my office I have an HP DL360P Gen8 server running Windows Server 2012 R2. It had three hard drives in it (each 600gb SAS 10K rpm) when it was purchased, and they were configured in RAID5. So,...
View ArticleRe: proliant ml10 gen9 displayport no video with active adapter
Hi Thanks for the response I did see the notice and didnt think it was that brand specific so last night I placed an order for the part. Hopefully it will resolve the issue....
View ArticleRe: HDD not detected (HP ProLiant DL360 Gen9)
I see you solved the issue by creating an array. If you don't want ot use RAID you can do one of the following. For the embedded "B" series Dynamic Smart controller, go into RBSU and change it from...
View ArticleRe: HP ACU - No controllers detected (DL380 Gen9)?
ACU has been replaced by HP SSA. From Intelligent Provisioning run HP SSA, or from RBSU, select setup and the disk controller and launch HP SSA
View ArticleSmart Array B140i - how many simultaneous RAID volumes?
Does anyone know how many simultaneous RAID volumes is supported on the B140i controller?Ideally I would like to have three volumes but not sure if this is suported? HPE support had no answer....
View ArticleRe: Smart Array B140i - how many simultaneous RAID volumes?
Have a look into the user guide - overview:https://h20565.www2.hpe.com/hpsc/doc/public/display?sp4ts.oid=7271241&docLocale=en_US&docId=emr_na-c04441385
View ArticleRe: HDD not detected (HP ProLiant DL360 Gen9)
another solution is herehttps://h20565.www2.hpe.com/hpsc/doc/public/display?sp4ts.oid=7271241&docLocale=en_US&docId=emr_na-c04441385
View ArticleRe: Questions about HP Proliant ML150 Gen9
For non-hotplug drives the caddy is included with the server, for hotplug disks the disk comes with the caddy.
View ArticleRe: Smart Array B140i - how many simultaneous RAID volumes?
Hi Torsten,I did have a look in the documentation however not completely sure if the answer is there.B140i supports up to 10 LUNs, so if one assumes RAID groups "analogous" to LUNs B140i might support...
View ArticleV2P o objectivo é usando o HP Insight Control server provisioning fazer um...
Hello, I need to make a V2P using HP Insight Control server provisioning.From a vmware VM Windows Server 2008 R2 to aerver Proliant DL380 G6Need tech assistance to proceed Thank you
View ArticleNeed help to create RAID in UEFI Shell
In Gen9, Is there a way to create RAID (hpssacli) in UEFI Shell before proceed to PXE boot (KickStart)?
View ArticleClik here to view.
Re: Smart Array B140i - how many simultaneous RAID volumes?
I think they assume 10x RAID 0 on 10 disks as a maximum.
View ArticleRe: iLo failure after firmware flash
No luck so far, unable to reflash firmware remotely any way I've tried. I'm hoping when i can get on site I can boot into a recovery environment like HP SUM or the intelligent provisioning menu and...
View ArticleRe: RAID array definition lost
So, no luck with getting the HP Proliant Service Pack. I ended up pulling the current drives and put in an old SATA drive, created a volume and set it as the default boot drive and then installed a new...
View ArticleML10 1611-Fan 1 Failure Fan Solution Not Sufficient False positive ?
Half a year ago I set up and run ML10 server. It worked properly. After 3 months it lost electricity. On power restore it failed to boot with this error:1611-Fan 1 FailureFan Solution Not...
View ArticleRe: HP ML10 v2: set the correct boot order for HDD
Did you ever determine if it is possible to select the boot drive? I'm trying to find out if I can use a PCIe SSD and I'm wondering if it is limited to only booting from the SATA connectors.
View Article