Re: P400i In Lock-up State after installing 512MB BBWC
The firwmware is the latest and the 512 cache is compatible, so you could try to reset the controller by doing following:power down the server, install the 512 module, remove all drives (remember their...
View ArticleRe: DIFFICULTY IN INSTALLING WINDOWS SERVER 2008 R2 in both HP ML10 and HP ML30
Ml30 Gen9 and Ml10 Gem9 Servers, do not support Windows Server 2008 R2. http://h17007.www1.hpe.com/us/en/enterprise/servers/supportmatrix/windows.aspx#.Wv8iTWiFOM8
View ArticleRe: P400i In Lock-up State after installing 512MB BBWC
Ok. I will try that and see what happens. Thanks.
View ArticleRe: Offline SSA 2.65 is not booting on DL380 G7 server
Hi krasinka1409, Thank you for your post, I have tried that before but it didn't work because I think it's only for Win 2008R2. I could fix that after updating firmware by...
View ArticleDisable Gen8 B120i raid controller
Hi everyone,I have a gen8 microserver with only one hard drive running hp custom esxi 6.5 on it. The default raid setup is 0 when one drive is in use, my question is, if I disable the raid controller...
View ArticleRe: Noisy Fan Server HPE PROLIANT DL 560 GEN10
thank you for the reply mr. summanI've tried with the latest firmware update (ilo 5 lattest update) but keep the noise on my server anyway .. usual noise occurs when the startup server or when the...
View ArticleDL380 G3 - Changing a Hard Disk
I have 2 older DL380 servers. I inherited my IT position here a couple of years ago, but have never had to do anything but maintenance on these things. Can a hard drive on thse be hot swapped like on...
View ArticleRe: NMI error in DL380p GEN 8 when P430/4GB is installed.
hi Edduhollandak - did you find a solution to this ?We have an identical system and config and am getting the same errorthank youbw
View ArticleRe: DL380 G3 - Changing a Hard Disk
Hi,Here is the QuickSpecs for this server.This server will support Hotplug hard drives, but if you have question about How to identify hotplug drives, then it can be identified by small maroon/red...
View ArticleDL 360 G7 and MDS600 IO Module
Hello,We have 3 ProLiant DL360 G7 with MDS600 Drive arrays.Every 2-3 months, one of these servers don't see the half of the drive array.This occurs always during database mainternance of these Exchange...
View ArticleProblems with ML110 G9 fans
Hello good afternoon.I recently added a P440 hardware controller to the ML110 G9, and I also purchased the fan kit for the PCI. The operating system is Windows Server 2016.Previously, when I was using...
View ArticleSmart Array P420i "could not be authenticated as a genuine HPE drive"
We have run into an issue a couple of times now with Gen8 servers claiming that drives could not be authenticated as a HPE drive. This is causing us issues beceause it is throwing off our RAID status...
View ArticleHP DL380 G6 link DELL MD1200 SAS Card Select
consultHP DL380 G6 link DELL MD1200 SAS Card Select HP？ or Dell(PERC H810)？HP DL380 G6 OS use is VM ESXI 6
View ArticleRe: Smart Array P420i "could not be authenticated as a genuine HPE drive"
Hi,Try some basic troubleshooting:1. Switch OFF the server and remove the power cord.2. Reseat all hard drives.3. Reseat cables between the controller and drive cage.4. Update server BIOS and hard...
View ArticleRe: iLO 4 not responding, SPP not loading, DL360 Gen8
Ok I'll create a kali bootstick with the firmware, but how do I flash it from inside the linux?
View ArticleRe: iLO 4 not responding, SPP not loading, DL360 Gen8
Hey, starting the SPP online is not the problem, did that before but that doesn't fix the iLO issue, I just wanted to use that to flash the firmware. resetting to factory defaults doesn't work...
View ArticleRe: Smart Array P420i "could not be authenticated as a genuine HPE drive"
I have tried the HPD6(D) firmware update in Windows but it reports:Update not attempted (or interrupted). All selected devices are either up-to-date or have newer versions installed.However, in HPE...
View ArticleHPE DL 380 G9 Agentless managment service :Not available
Hi;HPE DL 380 G9 Agentless managment service :Not available and in iLo federation --> Multi system map --> Do not display the server.Please guide me to fix this problem.
View ArticleIntelligent Provisioning version in SPP 2018.03
Hi,why is the version 2.7 of Intelligent Provisioning not included in the current SPP 2018.03?It's still version 2.55.Is it possible to include the 2.7 update file in the SPP manually so I can update...
View Article