Re: Windows Server 2012 on a DL380 G4 (Sort of)
I realize that this is a little late in the game but.... Just HOW did you manage to get Win2012 installed? I was elated to learn that, with a quick swap of the procs, I might get some additional use...
View ArticleHP Proliant ML335 (G5) - Best way to upgrade HD storage space
Currently we have an HP Proliant ML335 server with four 146GB SAS drives in a hardware RAID5 setup. The array is divided into 2 logical drives which are drive "C:" and drive "D:". See attached...
View ArticleRe: HP Proliant ML335 (G5) - Best way to upgrade HD storage space
>the manual states that the expansion works at the speed of about 1 GB per 15 minutes. Did it says that's when the system is under a heavy load and faster when idle?
View ArticleDL380e Gen8 - Can't use all 8 drive bays
Hi everyone, I have an 8-bay DL380e Gen8 with the P420 RAID Controller. I added 3 new HDD's to try and create a RAID-5, but one of the drives isn't recognized. Bays 1-4 are used without problems, but...
View ArticleRe: 1783 Slot 5 Drive Array Controller Failure
can anyone help then? I have now changed the smart array card to 642 card and still the same problem occurs 1783 - cmd=11h, err=020h. So, if I remove the SCSI cable from the back of 642 - the server...
View ArticleRe: Physical Memory (not all recognized by Windows)
What Windows version do you have? What Proliant model? What type of CPUs do you have?It would help if you explained your problem in words, in addition to your picture with circles around memory sizes.
View ArticleRe: HP ML350e Gen8 Fan Noise
Incredibly mine stopped making noise after I updated the whole firmware as it went from 75% to 43%.I also disconnected the Ambient temp connector!! Now I disabled the PCI Gen 3 in Advanced options and...
View ArticleHP ML350 G5 RAID 5 two drives failed.
Hello..Is it possible to recover a RAID5 volume when two drives in failed condition? One drive was in failed state and another one was predictive failure.
View ArticleRe: HP ML350 G5 RAID 5 two drives failed.
If two are failed, no. But if the predictive failure may not have completely failed.
View ArticleHP Microserver G8 wont boot after OS Installation
The device, just a few weeks old was working but has seemed a bit flakey since I got it. The current issue is the device wont see any storage onto which the operating system has been installed. The...
View ArticleRe: HP Microserver G8 wont boot after OS Installation
Hi: Maybe you can try to set your boot device order in RBSU, wrong device boot order may cause this error.
View ArticleRe: HP Microserver G8 wont boot after OS Installation
Hi, I did this. I tried setting the USB as the first device when I was installing to USB and the HDD to first device when I installed to the HDD. Thanks, T
View ArticleRe: DL380e Gen8 - Can't use all 8 drive bays
Hi, Do refer to the DL380e Gen8 User Guide.Refer to page#83 for Storage cabling. Make sure you have properly connected the SAS and power cables inside the server.In some scenarios both the ports on the...
View ArticleRe: Windows Server 2012 on a DL380 G4 (Sort of)
Hi, We tried to install Windows 2012 Foundation pack, the installation went well but later server became very slow and some times blue screens. Bluescreen message was pointing towards processor.We used...
View ArticleRe: Hp ProLiant ML150 G6 not booting up
Hi, Try to clear NVRAM from the System Board.Also try with a different processor if you have. Thank You!I am a HP employee.
View ArticleRe: Friendly Name on Broadcom NC373i
Hi, Try this link, it may help:http://superuser.com/questions/323331/how-to-get-rid-of-auto-generated-sequence-number-in-networks-device-name-in-win Thank You!I am a HP employee.
View ArticleRe: Installing Windows 7 X64 on Proliant ML110 G3
Hi, I guess ML110 G3 is not a 64bit compatible processor and chipset.Try with a 32bit Win7 if you have. But again, these servers are not tested for Windows 7 or 8 or Server 2012. Thank You!I am a HP...
View ArticleRe: HP Proliant DL370G6 - any option or controller to get eSATA port ?
Hi, Any third party eSATA controller plugged into PCI slot should work, but still HP does not have a compatibility list.You have to try on your own. Thank You!I am a HP employee.
View ArticleRe: iLO Shared Network port - locked out
Hi, How to reset iLO if it hangs on HP ProLiant Servers?HP Integrated Lights-Out 3 (iLO 3) Firmware - Password Reset. Thank You!I am a HP employee.
View Article