Hi Sanjeev,
Thanks for the link!
According to the matrix available through the link, the ML 350p, Windows Server 2016 is certified to work.
Has Server 2019 been shown not to work or has it just not been officially tested by HP? I imagine it would work by itself but would there be driver incompatibilities? As a hobbyist and second hand owner, I'm ok with "unofficial" and "uncertified" knowledge Server 2019 would work.
Has anyone recently installed 2016 or 2019 on their Gen8?
-- Boris
Hi everyone, I have a question about installing a second riser board on an HP Proliant DL 380 G7 server. I already have a riser board installed, but I noticed that there is another connector for a second riser board. Can I have two riser boards installed?
Live long and prosper
Marcelo Magalhães
Yes, there are several options for a second riser:
https://h20195.www2.hpe.com/v2/GetDocument.aspx?docname=c04199811
AmRa, thanks for the answer.
Any options to run a non-HPE graphics card?
Another bios for motherboard?
Thanks
hello,
Just have downloaded the last updated MIBs in HPE SIM MIB KIT and shared with customer for testing alarms. OID in shared MIBs are registered as 1.3.6.1.4.1.232.XXXX, although customer is receiving a different OID as 1.3.6.1.4.1.232.0.XXXX,
MIBs shared: cpqhlth
The server is a DL380 GEN 10 and the SNMP credentials are configured in iLO 5.
Where should i get the correct MIBs so i can share them and the Manager can identificate them correctly?, at this moment these are unrecognized alarms.
Thanks a lot,
Thank you for your reply. The current DL380 Gen10 server is used with two CPUs. I would like 871969-001 P2000
Plug in slot2 and 872323-001 P40 plug in slot4. Our leader asked to do this : ( , but I'm not sure if single-wide GPUs and double-wide GPUs can be mixed. Hope you can provide valuable suggestions, thank you
Hi Chowo ,
Was it like this since first time installation ?
Any changes done before the issue occured.
Is all the firmware / Drivers updated on the server ?
Is the Boot image locally installed or is it boot from SAN ?
Regards
Ronny
Thanks for providing the requested details. Please find the update:
https://h20195.www2.hpe.com/v2/gethtml.aspx?docname=a00008180enw
As per the server specifications, · Mixing of GPUs is not supported
Please refer to the shared link
Thank you
Hope we have answered your query.
Let us know if we were able to answer your query.
Thank you
Thank you very much!
My monitoring tool keep showing my Proliant D380 Gen10 has problem about the Memory.
But there's no error show in the iLO 5 console. I want to manual run a diagnostic test. How can I do that?
Is ILO up to date?
What is the exact message?
If you reboot ILO, it will perform a selftest.
My task is to wipe RAID array hard drives of decomissioned server and to forward server with drives to local school.
I tried UBCD HDD utilities (USB Boot disk) Active Killdisk utility which founds a RAID of 5.5Tb.
Does 5.5TB seems correct size of 4x2000 SAS RAID?
Server drives probably are not in original slots now.
To check RAID configuration fails - Entering HP Array Configurationduring during server boot fails, instead after F5 (and F10) server tries to boot from CD.
Is it safe to use Active Killdisk utility from USB Boot disk and does it wipes all disks?
Any ideas how to complete wipe task?
As I mentioned, it has been already checked.
Unfortunately this HP server doesn't know, what to do when F10 (or F5) is on screen during boot and is pressed on keyboard.
Actually my initial thread subject was How to fix F5 and F10 error but I changed it because there might be another easier way to complete my task.
I read earlier today that there is some kind of plague also in HP servers but descriptions how to fix were rather confusing or outdated..
And I hoped so much, that it's not now and here.
I am ready to create an ILO update media but didn't found any link where to download.
Any help is much appreciated.
Please advise cabability of installing three network adabters on DL380 G8/G10 servers in order to get 12 ports per server.