Re: HP ML115 G5 1610 Temperature Violation
Hi,I've got the same problem, I tried to update the Lights-Out 100 Remote Management Firmware but the server has shut down suddenly during the upgarde and now does not start. How can I recover it?Thank...
View ArticleRe: DL360 G4 Power Savings Mode?
OpenBSDBut we get the message before any operating system is booted.Before even the prompt about PFX for raid controller etc. In another message there was mention that the feature might not exist for...
View ArticleRe: Proliant DL380 G4 - Are sensors available?
Ok, so do you think that reinstalling last supported 3.5 ESXi will I obtain all of the information I would like to read? Thanks and regards
View ArticleRe: Proliant DL380 G4 - Are sensors available?
Of course, once you install the supported operating system, you can have all the features that come with it.
View ArticleClik here to view.
Re: DL360 G4 Power Savings Mode?
ProLiant servers support various power savings options, including Power Regulator for ProLiant and ACPI-based OSdemand-based switching.Included in Power Regulator for ProLiant is the HP Dynamic Power...
View ArticleRe: How to enable Embedded NICs on Proliant dl380 G5
Under System Optionsyou can find Embedded NICs Options:• Network Boot• Disabled I advice You to check Standard Boot Order (IPL)
View ArticleRe: hard drive GB0750C8047 is broken - which part to replace?
Preferably must change the faulty disc by its similar.
View ArticleRe: Add HDD ML350p g8 RAID10
to add HDD to Array, you can use ACU Array configuration utility you need FBWC installed on P420i Here QuicSpecs : http://h18000.www1.hp.com/products/quickspecs/14228_div/14228_div.pdf Once you add the...
View ArticleRe: How to enable Embedded NICs on Proliant dl380 G5
I tried that and no luck. The iscsi still show the mac addresses and the Nic aren't showing a mac address and say "disabled".
View ArticleRe: ML310 G5 AND SMART ARRAY P410 PROBLEM.
ok i give you HPS Report. In this moment sever start and when i power off, reboot, and power on the server recognize P410 correctly, i've done this: - remove P410 controller from server;- start server...
View ArticleRe: Add HDD ML350p g8 RAID10
Ok thanks for that, it has 512 of write cache, what difference does it make having and not having the cache ? If I want to expand the existing array is that possible or do I have to add the new drives...
View ArticleRe: Add HDD ML350p g8 RAID10
without the cache, there is some option that you can not do, such as the activation of RAID 5 or RAID 50 requires a minimum of 512M. you can not increase the size of a logical drive. more cache must...
View ArticleRe: ML310 G5 AND SMART ARRAY P410 PROBLEM.
Good Job, but the issue isn't on Controller card or Cache, I am sure that the issue is about configuration, Update Firmware Keep me informed :)
View ArticleRe: How to enable Embedded NICs on Proliant dl380 G5
can you post here a screenshoot of this issue please?
View ArticleRe: ML310 G5 AND SMART ARRAY P410 PROBLEM.
i've update all firmware, i've a reports if you want can give you, but file are 74MB, how can Iattacha private message? Thanks
View ArticleRe: ML310 G5 AND SMART ARRAY P410 PROBLEM.
Tested with cache module in, and after i've connected a cache accellerator controller crashes after startup, or on reboot intiate a lookup initializing. At this point i think with most probability the...
View ArticleRe: How to enable Embedded NICs on Proliant dl380 G5
so the First action Plan is : Use this lin to choose the appropriate OS and Update BIOS& iLO :...
View ArticleRe: How to enable Embedded NICs on Proliant dl380 G5
Done and Done! Both were already at that level, but I reinstalled it anyway. No change after the reinstall and reboot.
View Article