Re: ATA hard reset errors on DL320e v2 in AHCI mode with NCQ/write-cache...
I'm glad it was helpful. My standard practice for a lot of these servers (and some workstations) is to just throw in a LSI controller and run with it. Performance is uniform. Ports are uniform....
View ArticleRe: HPE ProLiant DL160 Gen9 Server & Matrox G200eH screen resolution problem
Thank you so much for the idea. This is a bit complicated, as no monitor connected to the server at this moment. We access it with ILO and Zoho Assist / Teamviewer (also have RDP connection from the...
View ArticleRe: ML370 G6 Won't Power On when NC375i is Plugged
Hi,I'll try and answer you, but I think it's hardware ´back’panel’´ !!
View ArticleRe: DL360 G7 all 4 HDDs in amber led error at boot
Hi,Please use HP Smart Start cd, https://support.hpe.com/hpsc/swd/public/detail?swItemId=MTX_2e6c41afdb8c4c0d9bffce484c&swEnvOid=4064#tab-historyBoot with it then access Array configuration utility...
View ArticleRe: Disk Drive Firmware Update Recommended
Hi,May be the SPP version you have used is not supported, or it may not have the latest firmware for these drive model .Which SPP version you have used ?I believe you need to use SPP 2017.04, or...
View ArticleRe: DL360Gen8 and 11020 Trap
The MIB's should by default be in the directoriy /opt/mx/mibsChecked the link and there are no pre-requisites mentiond hence it should be fine to...
View ArticleRe: SNMP - System health - Value from SNMP is different from real iLO value
Greetings!Please ensure the following points.1. There should not be any space before/after the OID as this can cause this error.2. Please check your Integrated Management Logs in iLO. Events in there...
View ArticleHP server one HDD showing Amper light continuasly
Dears , I have HP ML350 G8 Server with Raid 5 ( total 3 HDD) one of the disk failed and we replace it with new HDD (Hot Swap). But still the new HDD showing Amper light .
View ArticleRe: Can't configure B120i RAID Controller or boot into SSA
Hello,I hope all is well.Please follow the below customer advisory to configure raid from SSA.Title: HPE ProLiant ML10 v2 Server - Configuring Raid Array and Installing Operating...
View ArticleRe: Gen10 Array Controllers in mixed mode
Hello,I hope all is well.I think you are using the P816i-a controller not i816a. If yes, follow the below documents for more clarification.HPE Smart Array P816i-a Controller –...
View ArticleRe: Gen10 Array Controllers in mixed mode
Hi,thanks for your reply, I know these documents. I'm refering to https://kb.vmware.com/s/article/2129050If the vSAN disks are in pass-through/JBOD mode, the non-vSAN disks mustalsobe in...
View ArticleRe: DL360e Gen8 post message 261 - Server Platform Services Firmware Flash
I hope all is well.The servers running on very old BIOS and the firmware’s set and latest having several fixes and enhancement to apply for fixing the known issues and efficient troubleshooting.We...
View ArticleRe: Question about Smart Array B320i
Hello,I hope all is well.AS per shared information, you have to purchase the SAS license key for using SAS hard disk with the B320i controller.Please follow the below documents for more...
View ArticleClik here to view.
Re: Error when updating SSD firmware "Update not attempted. All selected...
Hello,I hope all is well.I would request you, take the complete data backup before the hard disk firmware updatePlease follow the advisory for more clarification on how to check the current firmware...
View ArticleRe: DL380 Gen9's hang booting from spp iso
Hi Kerry, I have had similar problems on a variety of different DL360s, eventually worked out that the HTML5 console seems to be the issue. If you use the Java console it works fine as normal, also...
View ArticleRe: Error when updating SSD firmware "Update not attempted. All selected...
Thank you, but clicking on the link says "Document not available". Please advise.
View ArticleDL380 G7 + Smart Array P822 capacitor recharging issue
I added a refurbished Smart Array P822 controller (with 2GB FBWC cache) to a DL380 G7 server. I'm getting the following error in IML. POST Error: 1798-Slot X Drive Array - Array Accelerator Self-Test...
View ArticleRe: Error when updating SSD firmware "Update not attempted. All selected...
Here is the correct document link is for drive model VK003840JWSST, which fails at 32,768 power-on hours:HPE SAS Solid State Drives - Critical Firmware Upgrade Required for Certain HPE SAS Solid State...
View ArticleRe: Error when updating SSD firmware "Update not attempted. All selected...
It looks like I'll need to install the SSA first. I tried doing so on the mgmt VM we run but apparently virtualized environments are not supported for the app, so I'll look to finding a physical and...
View ArticleRe: Error when updating SSD firmware "Update not attempted. All selected...
After looking into it a bit further, it looks like a reboot is needed after the SSD firmware update in order for both SSA and iLO to report the updated firmware version. Interested in knowing whether...
View Article