Moving disks to another server.
There are two identical servers. HP Proliant DL 380 G4 with Smart Array 6i in Embedded Slot. One of them was broken. We know nothing about its array configuration. Is it possible to move the disks to...
View ArticleASR detected by system ROM
Hello, colleagues!I have a server HP ProLiant ML350p Gen8 with Windows Server 2008 R2 Enterprise on board.Yesterday server was rebooted without my permission.At iLO log I found one event at time, when...
View ArticleReplacing failed drive
We've got an old ML370G3 server with a RAID 5 array consisting of 3 drives. One of the drives has failed. We've tried reseating the drive, but it isn't working. We've got 3 drives of the same model...
View ArticleRe: Moving disks to another server.
Yes you can move the disks over to the other system. The RAID configuration is stored on the disks, not the smart array controller. The only time you may run into an issue is if the smart array...
View ArticleRe: Moving disks to another server.
do you know what was on the original server? update the firmware on the replacement to the lates version and you won't have an issue
View ArticleSystem Management Homepage version 7.2.4.1
Hi I need to upgrade system management homepage on some servers, the upgrade looks straight forward enough. I just wanted someone to confirm if there is any pre reqs regarding what version of HP...
View ArticleRe: 350 g6 overtemp?
Server shuts down right away before fans have a chance to spin or any bios messages/errors show up. the reason i think it is overtemp is because that is only led that shows up on system board specs...
View ArticleWhere can I find drivers for the ML370T01?
I have a ML370T01, where can I find drivers? I have searched HP's website and found nothing. Not even any archive stuff. Looking for some drivers for the mobo and chipset etc. Thanks,
View ArticleUnable to get iLO2 working with Active Directory for authentication
Hi, all, I'm at my wits end. I'm trying to get an iLO-2 equipped server to use Active Directory for authentication and failing miserably. I've read dozens of posts and articles and used an HP utility...
View ArticleRe: Unable to get iLO2 working with Active Directory for authentication
I have my ILO 2 setup kind of similar... here's the settings I have:directory server address: domain.local (don't put in a specific domain controller address here, just use the domain name and let DNS...
View ArticleRe: System Management Homepage version 7.2.4.1
I don't know if you meant that 7.2.4.1 is the version of SMH you have, or the version you're upgrading to. I think there's a newer version out of SMH unless you're looking at something besides the...
View ArticleRe: Replacing failed drive
That should work fine. The array controller will see the "new" drive as a replacement for the failing one and rebuild onto it.If you're at all unsure, this is a good time to make backups just in case. :)
View ArticleRe: ASR detected by system ROM
I've seen issues sometimes where a server was rebooting but something was keeping it from doing it cleanly (some bad driver or service...not sure).When that happened the server would ASR, which looks...
View ArticleRe: Moving disks to another server.
2.84 is the last version. I found about it on HP site.Thank you for your help! We saved data from these disks.
View ArticleRe: Where can I find drivers for the ML370T01?
According to this thread it is the same as the ML370 G1.http://h30499.www3.hp.com/t5/ProLiant-Servers-ML-DL-SL/Compaq-Proliant-ML370T01/td-p/3880588#.U8ji6ppCS70 Just google for ML370 G1 drivers
View ArticleML350 Gen8 - Supply power to PCI Express
We have installed a USB3.0 card into the PCI Express slot but it requires a SATA power connection to function properly. Whats the best way of getting power to the card? The two issues i can see are...
View ArticleRe: ML350 Gen8 - Supply power to PCI Express
After investigating different kinds of cards I found 4 port cards that needs power and 2 port cards without this requirement. However, I guess an active hub would solve the problem.
View ArticleRe: ML350 Gen8 - Supply power to PCI Express
I installed a Startech 2 Port that had the SATA Power connector on it. I connected 2 x 2.5" USB HDD's direct to the card both of which appeared to work ok but when transfering large amounts of data im...
View Article