Re: UPS Compatibility DL385p
Hi, I am Using the Smart UPS from APC 1500 RMI2u and all what I have as problem is that the delay time before it reboots after the commercial Power commes back is not enough with 60 seconds as I first...
View ArticleRe: Problems with Proliant DL560 Gen 8 also DL360p Gen8
On 110 brand new DL360p Gen8 systems we have had the issue on at least 4 machines. One machine errored out even after changng MLB. Vance
View ArticleRe: problem of including. off ppm2
Hi, Not sure which Generation of ML350 you are having problem with, but if PPM2 led is amber/red it means that PPM2 is faulty or is missing. If the server has two processors, remove the processor 2 and...
View ArticleRe: Multiple iLo network setting change questions.
Good Morning Joaragon We have a mixture of operating systems, windows,esx,linux. iLo's ranging from iLo2 to iLo4. I currently use CPQLOCFG for SINGLE server tasks, reset iLo mainly. For the work i...
View ArticleHelp New controller card install
hi all How can i configure a new p400 in ACU if my server will not get past post when i power on thanks P.S. This thread has been moevd from Servers > General to ProLiant Servers (ML,DL,SL). - Hp...
View ArticleRe: Help New controller card install
This is really not too much information ... What server is it? I would first try to re-seat the cache module and disconnect disks and check if the server boots. Any error messages?
View ArticleRe: Help New controller card install
If a server does not complete POST then depending on the issue, it sometimes may not even get past to allow configure the hard drives into RAID array. More information such as the server model, the...
View ArticleRe: problem of including. off ppm2
HP Proliant ML350 G5We have a server with one processorIn the slot ppm have not installed the module ppmattaching a photo
View ArticleRe: DL380 G6 Wont boot Virtual Media
One update on this old topic. I just have a DL360 G6 next to me and i experienced the same problem with virtual media. Apparently the solution in this case was to remove the internal usb drive because...
View ArticleHP DL 380 g6 + Sas Expander / 2nd Hard Drive Cage
I have an existing Raid 50 on 8 SFF sas drives. I have ordered a sas expander card, and 2nd hard drive cage and (8) HD's. When I go to recable the sas expander card in - will it preserve my existing...
View ArticleRe: HP DL 380 g6 + Sas Expander / 2nd Hard Drive Cage
No problem.The sas expander just give you more connectors. You connect the existing P410i to the expander and the disk cages to the expander.When boot up, the controller will notice a drive position...
View ArticleWhat is the best practice with updating VMware HP-ESXi-5.1.0-standard...
Have DL360p Gen8 servers installed with HP's custom ESXi 5.1 image ISO. What is the best practice for updating / patching this going forward. I come across some VIB depots on hp.com I added this as a...
View ArticleMissing Base System Device
I recently reimaged my ML350 G4 from Windows 2003 Standard to 2008 Standard. Everything loaded correctly and there are no issues listed in Device Manager. Yet whenever I do a restart I keep getting a...
View ArticleRe: Missing Base System Device
This may help:http://h30499.www3.hp.com/t5/Windows-Server-2003/Base-System-Device-Drivers/td-p/4242368#.UhOANz8t2LM most likely the ILO driver is missing....
View ArticleRe: Looking for a small server that can minimize power consumption & heat
You should take a look at the new Gen8 MicroServer. It is small and very quiet. It has the embedded B120i RAID controller which will allow you to do RAID 1 with Windows and a few of the Linux...
View ArticleRe: Missing Base System Device
Tried installing the ILO driver but got the attached error.
View ArticleRe: DL380 G6 Wont boot Virtual Media
Is there another USB attached to the server? Like an USB KVM dongle?
View ArticleRe: Missing Base System Device
Double check that the ILO2 is enabled in the bios, sometimes they can show as disabled in there but windows still sees some of the hardware but the driver cant load properly.
View ArticleRe: Remote Insight interface error. .1.3.6.1.4.1.232.0.9006 interface error
Is this related? I'm having issues with some linux servers built on DL380G7 and DL685G7. There could be others.CIM_9009 The mouse cable for the remote Insight board on server has been disconnected.In...
View ArticleRe: DL380 G6 Wont boot Virtual Media
Hi,Nothing else was installed except the internal usb drive + sd card.Apparently in my case it wont boot virtual media if i have both connected. As soon as i removed the internal usb drive , it works....
View Article