Hi
Is there a fast way to do it, SPP or similiar? Usually I have had problems utilizing HP's smart / intelligent methods. The firmware level is no apx. 5/2017.
HPE ProLiant DL380 Gen9 E5-2620v4 8-Core (1 CPU)
P/N: 843556-425
Smart Array P440ar/2G Module
No ILO license
Four Win Server 2012-2016 VMs
HPE 32GBmicroSDMainstream Flash Media Kit -SD for ESXi
VMware vSphere Essentials 6 Kit
Veeam Backup & Replication Std f.VMware
Hi, thank you for all links, but unfortunately this doesnt solve ma problem.
Wehen I boot from this CD there is a message: No disk available for installing Operation System. - there are 2 HDDs 300GB
Then I tried with ACU, I booted the ACU CD and the same problem: ACU did not deteted any controllers on you system.
What have I to do to configure the RAID and HDD - I would like to mirror disk 1 to disk 2?
Hi,
Please find below the quickspecs for the e200 and p400 series controller:-
https://h20195.www2.hpe.com/v2/getdocument.aspx?docname=c04140724
https://h20195.www2.hpe.com/v2/getdocument.aspx?docname=c04111741
Only difference between e200/e200i and p400/p400i is that e200 is a card and e200i is integrated on the board and the same is with p400i and p400.
Please refer to the above quickspecs to check the types of drives supported.
Regards,
Bunsol
Thanks sudhirsingh ,
After my last post I did upgrade the system to Bios Version: 2.16_09-12-2019 (26 Sep 2019) , which was recommended, I will keep monitoring the server, in case of any panic , will do upgrade to newest FW.
Yeah, thats the way I know from Gen9 with Intelligent Provisioning v2.x. We installed some servers this way.
At IP v3 we can only select the HPE Smart Array P408i-a SR Gen10 with logical RAID-Volume or single SAS-Drive, depends on the Arry-configuration.
Sorry, can't upload image yet...
Meanwhile we have opened a case at HPE Support.
Regards
Hello
We have just replaced the battery in Smart array cache, but since then the cache is disabled:
# ssacli ctrl all show status
Smart Array P410i in Slot 0 (Embedded)
Controller Status: OK
Cache Status: Temporarily Disabled
Battery/Capacitor Status: OK
I tried to power off/on the server and iLO but it didn't help. Can I enable the cache by some command or is it some other error?
Thanks
Ondrej Vesely
More info:
# ssacli ctrl slot=0 show | grep -i cache
Cache Serial Number: PBCDF0CRH0RD66
Wait for Cache Room: Disabled
Cache Board Present: True
Cache Status: Temporarily Disabled
Cache Status Details: Cache disabled; ADG enabler missing.
Cache Disable Reason: Temporary disable condition. The cache has been disabled because a RAID6 volume is configured but the enablement mechanism is broken or missing.
Drive Write Cache: Disabled
Total Cache Size: 1.0
Total Cache Memory Available: 0.9
No-Battery Write Cache: Disabled
Cache Backup Power Source: Capacitors
Can someone explain to me why the Support Center page dedicated to Proliant MicroServers Gen10 contains a lot of downloads (manuals, drivers, etc) regarding iLO, if the Microserver Gen10 doesn't support iLO?
This is very deceiving. I have spent a lot of time trying to read about iLO, before discovering that this particular generation of the MicroServer does not support iLO.
Hi,
there is no more HPE NIC Teaming Software.
NIC Teaming is now completely included in Windows from Microsoft and HPE did no longer needs to deliver there own Teaming Software.
LACP is the best option, but it needs a Switch Port configuration.
Switch Independent is second Choice, it needs no Switch config, but only Outgoing Traffic is teamed.
Failover is the third choice, the Second Adapter is only Standby.
Hallo,
hättet ihr bitte einen Tip für mich? Ein PL DL380 Gen9 soll eine 2080Ti Grafikkarte bekommen. Bisher nicht mein Thema... Ich bin im Zweifel hinsichtlich des Platzes / Bauform / Steckplatz.
Vielleicht hat ja jemand genau in dieser Paarung etwas bereits verbaut?
Vielen Dank vorab!
thanks for this the settings you can chose change depending on selection
Teaming mode : LACP / switch independent / Static teaming - we will chose LACP
Load balance mode : Dynamic / Hyper-V Port / Adress Hash - will chose dynamic
Standby adapters : none all active
what u have told is true. but help me out in enabling the 1 gbps i did not even connect to the ilo port i did connect to the direct lan port and then to a managed switch. and my switch is 1gbps enabled. but it is still not working. and in the adv settings speed and duplex options show only 100 mbps as last option
I would like to try to otpimize the cost of server-switch networking, as SFP28 trancivers are quite expensive. Active optical cabling seems as quite effective solution, but I can't find any article or document to confirm interoperatibility. Does anybody have experience with HPE Ethernet 10/25Gb adapters and Cisco active optical cables? I don't exepct any technical issue, but formally speaking there is no document where interoperability is confirmed officially.
I'm considering HPE Eth 10/25Gb 2P 640FLR-SFP28 Adptr (817749-B21) and Cisco SFP-25G-AOC (active optical cable).
Thanks, Bojan
wrote: what u have told is true. but help me out in enabling the 1 gbps i did not even connect to the ilo port i did connect to the direct lan port and then to a managed switch. and my switch is 1gbps enabled. but it is still not working. and in the adv settings speed and duplex options show only 100 mbps as last option
Your responding to a thread that was create in 2013. It might be better to start a new thread and give all the details of your current issue such as what model server you are working with, and the switch type you are conencting to
have a ProLiant ML350p Gen8 that has firmware 2.55
Getting module cache failed, which firmware do i need to upgrade to exactly? i want to try that before getting replacement battery for cache.
thx you for reponse :
HP 2TB 3G SATA 7.2K rpm LFF (3.5-inch) Non-hot Plug Midline 1yr Warranty Hard
Good for installed
valided solution
HI,
I,m searching for these drive bays at the back of a 380 gen 10. However, i,m unable to find them. It seems they are nvme bays, and I would also like to put NVME, drives in them, but it,s a real puzzle to find out what the article numbers/ part numbers are and where you can order them.
Can anyone point me in the right direction ?
Greetings.
The best way to update a server's firmware is through the Service Pack for ProLiant (SPP). We recommend using the latest version of SPP - 2019.09.0
https://support.hpe.com/hpsc/swd/public/detail?swItemId=MTX_a6fe854af60d4b86a8905f0e27
Boot the server with the SPP image >> Select Automatic Update >> This will update the firmware versions of all the device installed in the server. This is called an Offline update method, this method will not update any driver versions.
Please Note: Please make sure the Drivers are up to date as per the recommendations from VMware.
Thank you
Greetings.
Yes, the Capacitor pack needs to be replaced when the below error is reported on the servers.
Refer to the HPE document from the below link
https://techlibrary.hpe.com/docs/iss/shared/gen9/error/Advanced/Content/231565.htm
Thank you
Greetings!
There is no iLO feature on the HPE ProLiant MicroServer Gen10 server.
The support center page is pulling up Gen10 related documents and not all are specific to the server in question. We will provide feedback.
